====================================================================== Control Commands for NEC Projector HT410,HT510,LT180,LT25,LT30,LT35, NP40,NP50,NP60, NP4000,NP4001,NP4100,NP4100W NP41,NP61,NP52,NP62 NP43,NP53,NP63,NP54,NP64 NP110,NP115,NP210,NP215,NP216 NP-U300X,NP-U250X,NP-U310W,NP-U260W NP-V300X,NP-V260X,NP-V230X,NP-V260,NP-V230 NP-V300W,NP-V260W,NP-V260R NP-VE282X,NP-VE281X,NP-VE280X NP-VE282,NP-VE281,NP-VE280 NP-PE401H NP-M282X,NP-M322X,NP-M362X,NP-M402X, NP-M322W,NP-M362W,NP-M402W NP-M332XS,NP-M302WS,NP-M352WS series No.BDT120019 Rev1.0.18p Copyright (C) NEC Display Solutions, Ltd. 2004 - 2014 ---------------------------------------------------------------------- Updated on April 18, 2014 ---------------------------------------------------------------------- This file contains information about NEC projector control commands. Model Name HT10 : HT410/HT510 LT10 : LT180 LT30s : LT25/LT30/LT35 NP60s : NP40/NP50/NP60 NP61s : NP41/NP61/NP52/NP62 NP64s : NP43/NP53/NP63/NP54/NP64 NP4000s: NP4000/NP4001/NP4100/NP4100W NP215s : NP110/NP115/NP210/NP215/NP216 U300 : NP-U300X/U250X/U310W/U260W V300 : NP-V300X/V260X/V230X/V260/V230/V300W/V260W/V260R VE282 : NP-VE282X/VE281X/VE280X/VE282/VE281/VE280 PE401 : NP-PE401H M402 : NP-M282X/M322X/M362X/M402X/M322W/M362W/M402W/M332XS/M302WS/M352WS ====================================================================== Contents 1. Projector Control 2. Interface Conditions 3. List of Commands 4. Command Descriptions 5. Response 6. Table of Response Error Codes ====================================================================== 1. Projector Control ---------------------------------------------------------------------- NEC projectors make use of control commands that control the functions of the projector via connection with a personal computer or another device. ====================================================================== 2. Interface Conditions ---------------------------------------------------------------------- Serial connection ---------------------------------------------------------------------- The communications method conforms to the RS-232C standard. Baud rate: 38400 bps Data length: 8 bits Parity bit: No parity Stop bits: 1 bit Communications mode: Full duplex The control connector is described below. [HT10/LT10/LT30s/NP60s/NP61s/NP64s] The PC CONTROL connector is a mini DIN 8-pin connector. 1 To TxD of PC 2 3 4 To GND of PC 5 6 7 To RxD of PC 8 * 2, 3, 5, 6, and 8 are used inside the projector. [NP4000s/NP215s/U300/V300/VE282/M402] The PC CONTROL connector is a D-SUB 9-pin connector. 1 2 To TxD of PC 3 To RxD of PC 4 5 To GND of PC 6 7 To CTS of PC 8 To RTS of PC 9 LAN connection (NP4000s/NP215s/U300/V300/M402) ---------------------------------------------------------------------- [ Wired LAN port ] LAN interface Communication speed : Auto setting (10/100Mbps) Certified standard : IEEE802.3 (10BASE-T) IEEE802.3u (100BASE-TX, Auto-Negotiation) A LAN connector (8 male RJ-45 connector) 1 TD+ Transmit data (+) 2 TD- Transmit data (-) 3 RD+ Receive data (+) 4 Not used 5 Not used 6 RD- Receive data (-) 7 Not used 8 Not used [Port Number] The TCP port number used is "7142". USB connection (VE282) ---------------------------------------------------------------------- This conforms to the USB2.0 standard. Transfer speed: Full Speed (supported) Endpoint: Control transfer Endpoint 0 Device class: Vendor-specific class USB2.0 Standard: Universal Serial Bus Specification Revision 2.0 Connector Specifications 1 VBUS (Power supply) 2 D- (- Signal) 3 D+ (+ Signal) 4 GND (Ground) * Depending on the USB host controller in the personal computer, the USB connection may fail to operate. When using a USB hub, please use a self-powered type, not a bus-powered type. When using a USB hub, connection to the first stage of the USB hub is recommended. ====================================================================== 3. List of Commands ---------------------------------------------------------------------- * Example for command ---------------------------------------------------------------------- Command name Example ---------------------------------------------------------------------- 006. RUNNING SENSE 00H 81H 00H 00H 00H 81H 007. COMMON DATA REQUEST 00H C0H 00H 00H 00H C0H 009. ERROR STATUS REQUEST 00H 88H 00H 00H 00H 88H 015. POWER ON 02H 00H 00H 00H 00H 02H 016. POWER OFF 02H 01H 00H 00H 00H 03H 018. INPUT SW CHANGE 02H 03H 00H 00H 02H CKS 020. PICTURE MUTE ON 02H 10H 00H 00H 00H 12H 021. PICTURE MUTE OFF 02H 11H 00H 00H 00H 13H 022. SOUND MUTE ON 02H 12H 00H 00H 00H 14H 023. SOUND MUTE OFF 02H 13H 00H 00H 00H 15H 024. ONSCREEN MUTE ON 02H 14H 00H 00H 00H 16H 025. ONSCREEN MUTE OFF 02H 15H 00H 00H 00H 17H 030-1. PICTURE ADJUST 03H 10H 00H 00H 05H CKS 030-2. VOLUME ADJUST 03H 10H 00H 00H 05H 05H CKS 030-4. IMAGE ADJUST 03H 10H 00H 00H 05H CKS 030-5. COLOR TEMPERATURE ADJUST 03H 10H 00H 00H 05H 13H CKS 030-6. WHITE BALANCE ADJUST 03H 10H 00H 00H 05H 14H CKS 030-8. KEYSTONE ADJUST 03H 10H 00H 00H 05H 15H CKS 030-10. SIGNAL LEVEL ADJUST 03H 10H 00H 00H 05H CKS 030-11. VIDEO MODE ADJUST 03H 10H 00H 00H 05H CKS 030-12. IMAGE MODE ADJUST 03H 10H 00H 00H 05H CKS 030-15. OTHER ADJUST 03H 10H 00H 00H 05H CKS 037. INFORMATION REQUEST 03H 8AH 00H 00H 00H 8DH 037-1. LAMP INFORMATION REQUEST 03H 8CH 00H 00H 00H 8FH 037-2. LAMP INFORMATION REQUEST 2 03H 94H 00H 00H 00H 97H 037-4. LAMP INFORMATION REQUEST 3 03H 96H 00H 00H 02H CKS 037-5. TEMP INFORMATION REQUEST 03H 99H 00H 00H 01H CKS 037-6. CARBON SAVINGS INFORMATION REQUEST 03H 9AH 00H 00H 01H CKS 037-7. LAMP INFORMATION REQUEST 4 03H 9BH 00H 00H 03H CKS 050. REMOTE KEY CODE 02H 0FH 00H 00H 02H CKS 053. LENS CONTROL 02H 18H 00H 00H 02H CKS 058. FORCED ONSCREEN MUTE SET 02H 19H 00H 00H 01H DATA CKS 060. GAIN PARAMETER REQUEST 2 03H 04H 00H 00H 03H CKS 061. LAMP COOLING TIME REQUEST 03H 8DH 00H 00H 00H 90H 077. MUTE CONTROL 02H 1AH 00H 00H 02H CKS 078-1. SETTING REQUEST 00H 85H 00H 00H 01H 00H CKS 078-2. RUNNING STATUS REQUEST 00H 85H 00H 00H 01H 01H CKS 078-3. INPUT STATUS REQUEST 00H 85H 00H 00H 01H 02H CKS 078-4. MUTE STATUS REQUEST 00H 85H 00H 00H 01H 03H CKS 078-5. MODEL NAME REQUEST 00H 85H 00H 00H 01H 04H CKS 078-6. COVER STATUS REQUEST 00H 85H 00H 00H 01H 05H CKS 079. FREEZE CONTROL 01H 98H 00H 00H 01H CKS 084. INFORMATION STRING REQUEST 00H D0H 00H 00H 03H 00H 00H 00H CKS 091. DIGITAL ZOOM REQUEST 03H 20H 00H 00H 00H 23H 092-2. DIGITAL ZOOM SET 03H 21H 00H 00H 04H CKS 097-1. MENU MODE REQUEST 03H B0H 00H 00H 01H 00H B4H 097-2. LANGUAGE REQUEST 03H B0H 00H 00H 01H 01H B5H 097-3. MENU COLOR SELECT REQUEST 03H B0H 00H 00H 01H 02H B6H 097-5. DISPLAY TIME REQUEST 03H B0H 00H 00H 01H 04H B8H 097-7. MESSAGE REQUEST 03H B0H 00H 00H 01H 06H BAH 097-8. LAMP MODE REQUEST 03H B0H 00H 00H 01H 07H BBH 097-10. CLOSED CAPTION REQUEST 03H B0H 00H 00H 01H 09H BDH 097-11. ORIENTATION REQUEST 03H B0H 00H 00H 01H 0AH BEH 097-12. BACKGROUND REQUEST 03H B0H 00H 00H 01H 0BH BFH 097-23. AUTO START REQUEST 03H B0H 00H 00H 01H 16H CAH 097-24. POWER MANAGEMENT REQUEST 03H B0H 00H 00H 01H 17H CBH 097-27. FAN MODE REQUEST 03H B0H 00H 00H 01H 1AH CEH 097-30. PANEL KEY LOCK REQUEST 03H B0H 00H 00H 01H 1DH D1H 097-32. COMMUNICATION REQUEST 03H B0H 00H 00H 01H 1FH D3H 097-33. DEFAULT SOURCE REQUEST 03H B0H 00H 00H 02H 20H DATA CKS 097-34. PJ ID ENABLE REQUEST 03H B0H 00H 00H 01H 21H D5H 097-35. PJ ID REQUEST 03H B0H 00H 00H 01H 22H D6H 097-39. TEST PATTERN REQUEST 03H B0H 00H 00H 01H 26H DAH 097-88. LAMP SELECT REQUEST 03H B0H 00H 00H 01H 57H 0BH 097-89. LAMP INTERVAL REQUEST 03H B0H 00H 00H 01H 58H 0CH 097-148. KEYSTONE SELECT REQUEST 03H B0H 00H 00H 01H 93H 47H 097-174. REMOTE SENSOR REQUEST 03H B0H 00H 00H 01H ADH 61H 097-196. WXGA MODE SETTING REQUEST 03H B0H 00H 00H 01H DATA1 CKS 097-239. 3D MODE REQUEST 03H B0H 00H 00H 01H DBH 8FH 097-240. DLP Link REQUEST 03H B0H 00H 00H 01H DCH 90H 097-241. 3D FORMAT REQUEST 03H B0H 00H 00H 01H DDH 91H 098-1. MENU MODE SET 03H B1H 00H 00H 02H 00H DATA CKS 098-2. LANGUAGE SET 03H B1H 00H 00H 02H 01H DATA CKS 098-3. MENU COLOR SELECT SET 03H B1H 00H 00H 02H 02H DATA CKS 098-5. DISPLAY TIME SET 03H B1H 00H 00H 02H 04H DATA CKS 098-7. MESSAGE SET 03H B1H 00H 00H 02H 06H DATA CKS 098-8. LAMP MODE SET 03H B1H 00H 00H 02H 07H DATA CKS 098-10. CLOSED CAPTION SET 03H B1H 00H 00H 02H 09H 00H BFH 098-11. ORIENTATION SET 03H B1H 00H 00H 02H 0AH CKS 098-12. BACKGROUND SET 03H B1H 00H 00H 02H 0BH DATA CKS 098-23. AUTO START SET 03H B1H 00H 00H 02H 16H DATA CKS 098-24. POWER MANAGEMENT SET 03H B1H 00H 00H 02H 17H DATA CKS 098-27. FAN MODE SET 03H B1H 00H 00H 02H 1AH DATA CKS 098-30. CONTROL PANEL KEY LOCK SET 03H B1H 00H 00H 02H 1DH DATA CKS 098-32. COMMUNICATION SPEED SET 03H B1H 00H 00H 02H 1FH DATA CKS 098-33. DEFAULT SOURCE SELECT SET 03H B1H 00H 00H 03H 20H CKS 098-34. PROJECTOR ID ENABLE SET 03H B1H 00H 00H 02H 21H DATA CKS 098-35. PROJECTOR ID SET 03H B1H 00H 00H 02H 22H DATA CKS 098-39. TEST PATTERN SET 03H B1H 00H 00H 04H 26H CKS 098-88. LAMP SELECT SET 03H B1H 00H 00H 02H 57H DATA CKS 098-89. LAMP INTERVAL SET 03H B1H 00H 00H 02H 58H DATA CKS 098-148. KEYSTONE SELECT SET 03H B1H 00H 00H 02H 93H DATA CKS 098-174. REMOTE SENSOR SET 03H B1H 00H 00H 02H ADH DATA CKS 098-196. WXGA MODE SETTING SET 03H B1H 00H 00H 02H DATA1 DATA2 CKS 098-239. 3D MODE SET 03H B1H 00H 00H 02H DBH DATA CKS 098-240. DLP Link SET 03H B1H 00H 00H 02H DCH DATA CKS 098-241. 3D FORMART SET 03H B1H 00H 00H 02H DDH DATA CKS 098-242. 3D L/R INVERT SET 03H B1H 00H 00H 01H DEH 93H 110. AUTO FUNCTIONS EXECUTE 03H B6H 00H 00H 01H CKS 305-1. BASE MODEL TYPE REQUEST 00H BFH 00H 00H 01H 00H CKS 305-2. VERSION INFORMATION REQUEST 00H BFH 00H 00H 02H 01H CKS 305-3. PROJECTOR INFORMATION REQUEST 00H BFH 00H 00H 01H 02H CKS 307. AUTO ADJUST EXECUTE 2 03H BAH 00H 00H 01H DATA CKS * Availability by Model ---------------------------------------------------------------------- Model No. ------------------------- 01 : HT410/510 02 : LT180 03 : LT25/30/35 04 : NP40/50/60 05 : NP4000/4001 06 : NP41/61/52/62 07 : NP4100/4100W 08 : NP110/115/210/215/216 09 : NP43/53/63/54/64 10 : NP-U300X/U250X/U310W/U260W 11 : NP-V300X/V260X/V230X/V260/V230/V300W/V260W/V260R 12 : NP-VE282X/VE281X/VE280X/VE282/VE281/VE280 13 : NP-PE401H 14 : NP-M282X/NP-M322X/NP-M362X/NP-M402X/NP-M322W/NP-M362W NP-M402W/NP-M332XS/NP-M302WS/NP-M352WS Meaning of Symbol ----------------------------------------------------- * : Supported ! : Is available depending on the model's version - : Not supported Availability by Model -------------------------------------------------------------------------------- Command Name 01 02 03 04 05 06 07 08 09 10 11 12 13 14 -------------------------------------------------------------------------------- 006. RUNNING SENSE - - - - * * * * * * * * * * 007. COMMON DATA REQUEST - - - - * * * * * * * * * * 009. ERROR STATUS REQUEST * * * * * * * * * * * * * * 015. POWER ON * * * * * * * * * * * * * * 016. POWER OFF * * * * * * * * * * * * * * 018. INPUT SW CHANGE * * * * * * * * * * * * * * 020. PICTURE MUTE ON * * * * * * * * * * * * * * 021. PICTURE MUTE OFF * * * * * * * * * * * * * * 022. SOUND MUTE ON * * * - * * * * * * * * * * 023. SOUND MUTE OFF * * * - * * * * * * * * * * 024. ONSCREEN MUTE ON * * * * * * * * * * * * * * 025. ONSCREEN MUTE OFF * * * * * * * * * * * * * * 030-1. PICTURE ADJUST Brightness - - - - * * * * * * * * * * Contrast - - - - * * * * * * * * * * Color - - - - * * * * * * * * * * Hue - - - - * * * * * * * * * * Sharpness - - - - * * * * * * * * * * 030-2. VOLUME ADJUST Volume - - * - * * * * * * * * * * Bass - - - - - - - - - - - - - - Treble - - - - - - - - - - - - - - Balance - - - - - - - - - - - - - - 030-4. IMAGE ADJUST - - - - ! - * - - - - - - - 030-5. COLOR TEMPERATURE ADJUST - - - - ! * * * * - * - - * 030-6. WHITE BALANCE ADJUST - - - - ! - * - - - - - - - 030-8. KEYSTONE ADJUST H Keystone - - - - ! - * - - - - - - - V Keystone - - - * ! * * * * * * * * * 030-10. SIGNAL LEVEL ADJUST R/G/B Gain - Red - - - - ! - * - - - - - - - R/G/B Gain - Green - - - - ! - * - - - - - - - R/G/B Gain - Blue - - - - ! - * - - - - - - - 030-11. VIDEO MODE ADJUST Gamma - - - - ! ! * * * - * * - * Noise Reduction - - - - ! ! * * * - * * - * Select Color Matrix - - - - ! - * - - - - - - - Telecine - - - - ! ! * * * - * - - * 030-12. IMAGE MODE ADJUST Aspect Ratio Input Signal - - - - * ! * * * * * * * * 030-15. OTHER ADJUST Overscan - - - - ! - * - - - - - - - Picture Management - - - - - ! - * * - * * - * Base Setting / Reference - - - - - ! - * * - * - - * Wall Color - - - - - ! - * * - * * - * Dynamic Contrast - - - - - - - * - - * * - * 037. INFORMATION REQUEST * * * * * * * * * * * * * * 037-1. LAMP INFORMATION REQUEST * * * - - * - * * * * * * * 037-2. LAMP INFORMATION REQUEST 2 - - - - - * - * * * * * * * 037-4. LAMP INFORMATION REQUEST 3 - - - * * * * * * * * * * * 037-5. TEMP INFORMATION REQUEST - - - * - * - * * * * * * * 037-6. CARBON SAVINGS INFORMATION REQUEST - - - - - - - * * - * * - * 037-7. LAMP INFORMATION REQUEST 4 - - - - - - - * * - * * - * 050. REMOTE KEY CODE * * * * * * * * * * * * * * 053. LENS CONTROL Zoom - - - - ! - * - - - - - - - Focus - - * * ! * * - * - - - - - Lens Shift (H) - - - - ! - * - - - - - - - Lens Shift (V) - - - - ! - * - - - - - - - Stop - - - - ! * * - * - - - - - 058. FORCED ONSCREEN MUTE - - - - ! - * - - - - - - - 060. GAIN PARAMETER REQUEST 2 - - - - * * * * * * * * * * 061. LAMP COOLING TIME REQUEST - - - - ! - * - - - - - - - 077. MUTE CONTROL * * * * * * * * * * * * * * 078-1. SETTING REQUEST - - - - * * * * * * * * * * 078-2. RUNNING STATUS REQUEST - - - - * * * * * * * * * * 078-3. INPUT STATUS REQUEST - - - - * * * * * * * * * * 078-4. MUTE STATUS REQUEST - - - - * * * * * * * * * * 078-5. MODEL NAME REQUEST - - - - * * * * * * * * * * 078-6. COVER STATUS REQUEST - - - - - - - - * * - - - * 079. FREEZE CONTROL Freeze start - - - * * * * * * * * * * * Freeze cancel - - - * * * * * * * * * * * 084. INFORMATION STRING REQUEST - - - - - * - * * * * * - * 091. DIGITAL ZOOM REQUEST - - - - ! - * - - - - - - - 092-2. DIGITAL ZOOM SET - - - - ! - * - - - - - - - 097-1. MENU MODE REQUEST - - - - ! - * - - - - - - - 097-2. LANGUAGE REQUEST - - - - ! - * - - - - - - - 097-3. MENU COLOR SELECT REQUEST - - - - ! - * - - - - - - - 097-5. DISPLAY TIME REQUEST - - - - ! - * - - - - - - - 097-7. MESSAGE REQUEST - - - - ! - * - - - - - - - 097-8. LAMP MODE REQUEST - - - - ! * * * * * * * * * 097-10. CLOSED CAPTION REQUEST - - - - - - - * - - * * - * 097-11. ORIENTATION REQUEST - - - - ! * * * * - * * - * 097-12. BACKGROUND REQUEST - - - - ! - * - - - - - - - 097-23. AUTO START REQUEST - - - - ! - * - - - - - - - 097-24. POWER MANAGEMENT REQUEST - - - - ! - * - - - - * - - 097-27. FAN MODE REQUEST - - - - ! * * * * - * * - * 097-30. PANEL KEY LOCK REQUEST - - - - ! - * - - - - - - - 097-32. COMMUNICATION SPEED REQUEST - - - - ! - * - - - - - - - 097-33. DEFAULT SOURCE REQUEST - - - - ! - * - - - - - - - 097-34. PJ ID ENABLE REQUEST - - - - ! * * * * - * - - * 097-35. PJ ID REQUEST - - - - ! * * * * - * - - * 097-39. TEST PATTERN REQUEST - - - - ! - * - - - - - - - 097-88. LAMP SELECT REQUEST - - - - ! - * - - - - - - - 097-89. LAMP INTERVAL REQUEST - - - - ! - * - - - - - - - 097-148. KEYSTONE SELECT REQUEST - - * * ! * * - * - - - - * 097-174. REMOTE SENSOR REQUEST - - - - ! - * - - - - - - - 097-196. WXGA MODE SETTING REQUEST - - - - - - - * * - * * - * 097-239. 3D MODE REQUEST - - - - - - - - - - ! * - * 097-240. DLP Link REQUEST - - - - - - - - - - ! * - * 097-241. 3D FORMAT REQUEST - - - - - - - - - - ! - - * 098-1. MENU MODE SET - - - - ! - * - - - - - - - 098-2. LANGUAGE SET - - - - ! - * - - - - - - - 098-3. MENU COLOR SELECT SET - - - - ! - * - - - - - - - 098-5. DISPLAY TIME SET - - - - ! - * - - - - - - - 098-7. MESSAGE SET - - - - ! - * - - - - - - - 098-8. LAMP MODE SET - - - * ! * * * * * * * * * 098-10. CLOSED CAPTION SET - - - - - - - * - - * * - * 098-11. ORIENTATION SET - - - * * * * * * * * * * * 098-12. BACKGROUND SET - - - - ! - * - - - - - - - 098-23. AUTO START SET - - - - ! - * - - - - - - - 098-24. POWER MANAGEMENT SET - - - - ! ! * * * * * * * * 098-27. FAN MODE SET - - - - ! * * * * - * * - * 098-30. PANEL KEY LOCK SET - - - - ! - * - - - - - - - 098-32. COMMUNICATION SPEED SET - - - - ! - * - - - - - - - 098-33. DEFAULT SOURCE SET - - - - ! - * - - - - - - - 098-34. PJ ID ENABLE SET - - - - ! * * * * - * * - * 098-35. PJ ID SET - - - - ! * * * * - * * - * 098-39. TEST PATTERN SET - - - - ! - * - - - - - - - 098-88. LAMP SELECT SET - - - - ! - * - - - - - - - 098-89. LAMP INTERVAL SET - - - - ! - * - - - - - - - 098-148. KEYSTONE SELECT SET - - - * - * - - * - - - - - 098-174. REMOTE SENSOR SET - - - - ! - * - - - - - - - 098-196. WXGA MODE SETTING SET - - - - - - - * * - * * - - 098-239. 3D MODE SET - - - - - - - - - - ! * - * 098-240. DLP Link SET - - - - - - - - - - ! - - * 098-241. 3D FORMAT SET - - - - - - - - - - ! - - * 098-242. 3D L/R INVERT SET - - - - - - - - - - ! * - * 110. AUTO FUNCTIONS EXECUTE - - ! * - * - - * - - - - - 305-1. BASE MODEL TYPE REQUEST * * * * * * * * * * * * * * 305-2. VERSION INFORMATION REQUEST - - - * - * - * * - * * - * 305-3. PROJECTOR INFORMATION REQUEST * * * * * * * * * * * * * * 307. AUTO ADJUST EXECUTE 2 - - - - - - - * * - * * - * (!) LT30 : firmware version. 1.03 or later NP4000 : firmware version. 1.04 or later NP4001 : firmware version. 1.01 or later NP61s : firmware version. 1.02 or later V300 : firmware version. 2.03 or later ====================================================================== 4. Command Descriptions ---------------------------------------------------------------------- Precautions with Inscriptions: (*1) Control ID This refers to the Control ID. (*2) Model code : "xxH" inscription This will differ depending on the projector. In case of HT10, LT10, LT30s, NP60s series D0H In case of NP61s, NP64s, NP215s, V300, VE282, M402 20H In case of NP4000s, U300, PE401 series 80H (*3) Checksum : "CKS" inscription This is the value of the lower 8 bits of the results calculated in byte units from all the of the data up to the immediately preceding data. Example) 20H 81H 01H 60H 01H 00H 03H + + + + + + = CKS (*4) Response error number This is the value of the error number at the time of an error. See "NAK" of "6. Table of Response Error Codes". (*5) Term "RGB" and "COMPUTER" On the HT10 series, the term "RGB connector" has been changed to "COMPUTER". Supplement: * These specifications include response for items that the HT10s do not support. 006. RUNNING SENSE ********************************************************************** Function: This command acquires the operation mode of the projector. Command: 00H 81H 00H 00H 00H 81H Response: At the time of a success 20H 81H 01H xxH 01H DATA01 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Status of operation Bit 7 : Power On/Off processing 0 = No execution(Normal condition) 1 = During execution Bit 6 : Selecting signal processing 0 = No execution(Normal condition) 1 = During execution Bit 5 : Cooling processing 0 = No execution(Normal condition) 1 = During execution Bit 4 : External control mode 0 = OFF 1 = ON Bit 3 : No power-off period 0 = Power-off possible (Normal condition) 1 = Power-off Impossible Bit 2 : Reserved Bit 1 : Projector status 0 = Idling 1 = Power On Bit 0 : Reserved Response: At the time of a failure A0H 81H 01H xxH 02H DATA1H DATA02 CKS (*1) (*2) (*4) (*3) 007. COMMON DATA REQUEST ********************************************************************** Function: This command acquisition of the detailed conditions of the projector. Command: 00H C0H 00H 00H 00H C0H Response: At the time of a success 20H C0H 01H xxH 80H DATA01 .. DATA128 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Projector type See DATA70...71 DATA02 Control ID 1 .. 254 DATA03 Reserved DATA04 Projector status 00H : Idling 01H : Power On DATA05 Cooling processing 00H : No execution(Normal condition) 01H : During execution DATA06 Indication signal number( Entry list number - 1 ) 0 .. 199 DATA07 Type 1 of input terminal to be selected (!) 01H : 1 02H : 2 03H : 3 04H : 4 05H : 5 DATA08 Type 2 of input terminal to be selected (!)(!!) 01H : Computer 02H : VIDEO 03H : S-VIDEO 04H : COMPONENT 05H : Reserved 06H : Computer(DVI/HDMI) 07H : VIEWER 08H : SLOT1 09H : SLOT2 20H : DVI-D 21H : HDMI (1-5) 22H : DisplayPort (1-5) 23H : VIEWER (6-10) 24H : HDMI (6-10) 25H : DisplayPort (6-10) DATA09 Indication signal type * Valid only when Type 2 of input terminal is 02H or 03H x0H : NTSC3.58 x1H : NTSC4.43 x2H : PAL x3H : PAL60 x4H : SECAM x5H : B/W60 x6H : B/W50 x7H : PALNM x8H : NTSC3.58 LBX x9H : NTSC3.58 SQZ xDH : NTSC xEH : PAL-M xFH : PAL-N * x: undefined DATA10 .. 12 Reserved ( undefined ) DATA13 .. 20 Horizontal frequency of the indication signal(string) ( "000.00" kHz + NULL(0)+ NULL(0) ) DATA21 .. 28 Vertical frequency of the indication signal(string) ( "000.00" Hz + NULL(0)+ NULL(0) ) DATA29 Picture mute 00H : OFF 01H : ON DATA30 Sound mute 00H : OFF 01H : ON DATA31 .. 32 Reserved DATA33 Test pattern display 1 00H : No display(Normal condition) 00H Other : Displaying(Pattern ID) +------------+-----------------+---------+-------+--------+ | Pattern ID | Pattern name | NP4000s | NP61s | NP215s | | | | | NP64s | V300 | | | | | | VE282 | | | | | | M402 | +------------+-----------------+---------+-------+--------+ | 02H | Cross Hatch | * | * | * | | 03H | Gray Bars | x | x | x | | 04H | Raster(0%) | * | * | * | | 05H | Raster(25%) | * | x | * | | 06H | Raster(50%) | * | x | * | | 07H | Raster(100%) | * | * | * | | 08H | Focus | x | x | x | | 09H | Raster Blue | * | * | * | | 0AH | Gray Raster 30 | * | * | * | | 17H | Gray Raster 10 | * | * | * | | 18H | RAMP WBGR | x | * | * | | 19H | Blue Raster 60 | * | * | * | | 1DH | Cross Hatch 3 | x | x | x | +------------+-----------------+---------+-------+--------+ * : Supported x : Not supported DATA34 Test pattern display 2 FFH : No display(Normal condition) FFH Other : Displaying Bit 2 : BLUE pattern 0 = OFF 1 = ON Bit 1 : GREEN pattern 0 = OFF 1 = ON Bit 0 : RED pattern 0 = OFF 1 = ON DATA35 .. 50 Reserved DATA51 .. 65 User registration name ( 14 characters + NULL ) DATA66 Forced On-screen mute 00H : OFF 01H : ON DATA67 On-screen display 00H : No display 01H : Displaying DATA68 Selecting signal processing 00H : No execution(Normal condition) 01H : During execution DATA69 Status of operation 00H : Idling 04H : Power On 05H : Cooling 06H : Idling(Error occurrence) Other than above : (nondisclosure) internal use of code during a state transition period DATA70 .. 71 Projector type +--------+--------+--------+-------------------+ | DATA01 | DATA70 | DATA71 | | +--------+--------+--------+-------------------+ | 08H | 00H | 07H | NP4000 | | 08H | 00H | 10H | NP4100 | | 08H | 01H | 10H | NP4100W | | 11H | 00H | 00H | NP41/61 | | 11H | 01H | 00H | NP52/62 | | 11H | 00H | 12H | NP64 | | 11H | 01H | 12H | NP54 | | 11H | 02H | 12H | NP63 | | 11H | 03H | 12H | NP43 | | 11H | 04H | 12H | NP53 | | 11H | 00H | 11H | NP215 | | 11H | 01H | 11H | NP210 | | 11H | 02H | 11H | NP115 | | 11H | 03H | 11H | NP110 | | 11H | 04H | 11H | NP216 | | 14H | 01H | 10H | NP-U250X | | 14H | 02H | 10H | NP-U300X | | 14H | 03H | 10H | NP-U260W | | 14H | 04H | 10H | NP-U310W | | 14H | 00H | 11H | NP-PE401H | | 16H | 00H | 10H | NP-V300X | | 16H | 01H | 10H | NP-V260X | | 16H | 02H | 10H | NP-V230X | | 16H | 03H | 10H | NP-V260 | | 16H | 04H | 10H | NP-V230 | | 16H | 05H | 10H | NP-V300W | | 16H | 06H | 10H | NP-V260W | | 16H | 07H | 10H | NP-V260R | | 16H | 00H | 11H | NP-VE282X | | 16H | 01H | 11H | NP-VE281X | | 16H | 02H | 11H | NP-VE280X | | 16H | 03H | 11H | NP-VE282 | | 16H | 04H | 11H | NP-VE281 | | 16H | 05H | 11H | NP-VE280 | | 22H | 00H | 10H | NP-M402X | | 22H | 01H | 10H | NP-M362X | | 22H | 02H | 10H | NP-M322X | | 22H | 03H | 10H | NP-M282X | | 22H | 04H | 10H | NP-M402W | | 22H | 05H | 10H | NP-M362W | | 22H | 06H | 10H | NP-M322W | | 22H | 07H | 10H | NP-M332XS | | 22H | 08H | 10H | NP-M352WS | | 22H | 09H | 10H | NP-M302WS | +--------+--------+--------+-------------------+ DATA72 PC Card insertion 00H : Not inserted 01H : Inserted DATA73 USB Mouse connection 00H : Not connected 01H : Connected DATA74 Entry list type 01H : Default 02H : User DATA75 .. 82 Reserved DATA83 On-screen mute 00H : OFF 01H : ON DATA84 Reserved DATA85 Indicate Contents 00H = Picture signal displaying 01H = No signal 02H = Viewer displaying 03H = Test pattern displaying 04H = LAN displaying DATA86 .. 128 Reserved Response: At the time of a failure A0H C0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) (!) +--------------------------+-----------+----------------+ | Selected input terminal | DATA07 | DATA08 | +--------------------------+-----------+----------------+ | Computer1 | 1 (01H) | COMPUTER (01H) | | Computer2 | 2 (02H) | COMPUTER (01H) | | Computer3(DVI)/HDMI/HDMI1| 1 (01H) | DIGITAL (06H) | | HDMI2 | 2 (02H) | DIGITAL (06H) | | Component | 3 (03H) | COMPONENT(04H) | | Video | 1 (01H) | VIDEO (02H) | | S-Video | 1 (01H) | S-VIDEO (03H) | | USB-A(Viewer) | 1 (01H) | VIEWER (07H) | | LAN | 2 (02H) | VIEWER (07H) | | USB-B | 4 (04H) | VIEWER (07H) | +--------------------------+-----------+----------------+ Supplement: (!!) On the U300 series, this parameter becomes F0H when non signal. 009. ERROR STATUS REQUEST ********************************************************************** Function: This command acquires the error information occurring with the projector. Command: 00H 88H 00H 00H 00H 88H Response: At the time of a success 20H 88H 01H xxH 0CH DATA01 ... DATA12 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- * The various bits are normal is "0" and error is "1". * "None" is "0" fixation. DATA01 Error Status(1) bit0 : Lamp cover error bit1 : Temperature error(Bimetal) bit2 : None bit3 : None bit4 : Fan error bit5 : Power error bit6 : Lamp(or Lamp1) error bit7 : Lamp(or Lamp1) has reached its end of life DATA02 Error Status(2) bit0 : Lamp(or Lamp1) has been used beyond its limit bit1 : DMD error bit2 : Lamp2 error bit3 : None bit4 : None bit5 : None bit6 : None bit7 : None DATA03 Error Status(3) bit0 : None bit1 : FPGA error bit2 : Temperature error(Sensor) bit3 : Lamp(or Lamp1) housing error (!) bit4 : Lamp(or Lamp1) data error (!) bit5 : Mirror cover error bit6 : Lamp2 has reached its end of life bit7 : Lamp2 has been used beyond its limit DATA04 Error Status(4) bit0 : Lamp2 housing error bit1 : Lamp2 data error bit2 : High temperature due to dust pile-up bit3 : A foreign object sensor error bit4 : Pump error bit5 : Ballast communication error bit6 : None bit7 : None DATA05 .. 12 Reserved Response: At the time of a failure A0H 88H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 015. POWER ON ********************************************************************** Function: This command switches on the main power of the projector. Command: 02H 00H 00H 00H 00H 02H Response: At the time of a success 22H 00H 01H xxH 00H CKS (*1) (*2) (*3) Response: At the time of a failure A2H 00H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: * The projector does not accept the other command during power on processing. 016. POWER OFF ********************************************************************** Function: This command switches off the main power of the projector. Command: 02H 01H 00H 00H 00H 03H Response: At the time of a success 22H 01H 01H xxH 00H CKS (*1) (*2) (*3) Response: At the time of a failure A2H 01H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: * The projector doesn't accept the other command during power off processing.( It contains a cooling period.) 018. INPUT SW CHANGE ********************************************************************** Function: This command switches the input terminal. Command: 02H 03H 00H 00H 02H 01H DATA01 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Switching number +-----------+---------------------------+------+-------------+---------+---------+---------+-------+------+ | Switching | Terminal name | HT10 | LT30s/NP60s | NP4000s | U300 | VE282 | PE401 |M402 | | number | | LT10 | NP61s/NP64s | | V300 | | | | | | | | NP215s | | | | | | +-----------+---------------------------+------+-------------+---------+---------+---------+-------+------+ | 01H | Computer1(RGB1/RGB) | * | * | * | * | * | * | * | | 02H | Computer2 | x | *(!1) | * | *(!3) | x | x | x | | 1AH | Computer3(DVI)/HDMI/HDMI1 | x | x | * | *(!4) | *(!5) | * | * | | 1BH | HDMI2 | x | x | x | x | x | * | * | | 06H | Video | * | * | * | * | * | * | * | | 0BH | S-Video | * | * | * | * | x | * | x | | 10H | Component | x | x | * | x | x | x | x | | 11H | Component | * | x | x | x | x | x | x | | 1FH | USB-A(Viewer) | x | *(!2) | x | x | x | x | * | | 20H | LAN | x | x | x | x | x | x | * | | 22H | USB-B | x | x | x | x | x | x | * | | A1H | HDMI1 | x | x | x | x | x | x | * | | A2H | HDMI2 | x | x | x | x | x | x | * | +-----------+---------------------------+------+-------------+---------+---------+---------+-------+------+ * : Supported x : Not supported (!1)NP216 only (!2)NP52/NP62/NP54/NP64 only (!3)Except NP-V230X/NP-V260/NP-V230/NP-V260R (!4)Except NP-V230X/NP-V260/NP-V230 (!5)Except NP-VE280X/NP-VE280 Response: At the time of a success 22H 03H 01H xxH 01H DATA01 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Results 00H : Normal FFH : Error Response: At the time of a failure A2H 03H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Command example: * When switch to the Video connector 02H 03H 00H 00H 02H 01H 06H 0EH 020. PICTURE MUTE ON ********************************************************************** Function: This command blanks the picture. Command: 02H 10H 00H 00H 00H 12H Response: At the time of a success 22H 10H 01H xxH 00H CKS (*1) (*2) (*3) Response: At the time of a failure A2H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: * Picture mute is cancelled for the following: Input connector switching Video signal switching 021. PICTURE MUTE OFF ********************************************************************** Function: This command cancels the blank picture condition. Command: 02H 11H 00H 00H 00H 13H Response: At the time of a success 22H 11H 01H xxH 00H CKS (*1) (*2) (*3) Response: At the time of a failure A2H 11H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 022. SOUND MUTE ON ********************************************************************** Function: This command mutes the sound. Command: 02H 12H 00H 00H 00H 14H Response: At the time of a success 22H 12H 01H xxH 00H CKS (*1) (*2) (*3) Response: At the time of a failure A2H 12H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: * Sound mute is cancelled for the following: Input connector switching Video signal switching Volume adjustment 023. SOUND MUTE OFF ********************************************************************** Function: This command cancels the sound muting. Command: 02H 13H 00H 00H 00H 15H Response: At the time of a success 22H 13H 01H xxH 00H CKS (*1) (*2) (*3) Response: At the time of a failure A2H 13H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 024. ONSCREEN MUTE ON ********************************************************************** Function: This command blanks the on-screen display. Command: 02H 14H 00H 00H 00H 16H Response: At the time of a success 22H 14H 01H xxH 00H CKS (*1) (*2) (*3) Response: At the time of a failure A2H 14H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: * Onscreen mute is cancelled for the following: Input connector switching Video signal switching 025. ONSCREEN MUTE OFF ********************************************************************** Function: This command cancels the blanking of the on-screen display. Command: 02H 15H 00H 00H 00H 17H Response: At the time of a success 22H 15H 01H xxH 00H CKS (*1) (*2) (*3) Response: At the time of a failure A2H 15H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 030-1. PICTURE ADJUST ********************************************************************** Function: This command adjusts the Picture. Command: 03H 10H 00H 00H 05H DATA01 .. DATA05 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Adjustment items 00H : Brightness 01H : Contrast 02H : Color 03H : Hue 04H : Sharpness DATA02 FFH fixed DATA03 Adjustment mode 00H : Absolute value specification 01H : Relative value specification DATA04 Adjustment value ( Lower ranking 8 bits ) DATA05 Adjustment value ( Upper ranking 8 bits ) Response: At the time of a success 23H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Results 0000H : Normal 0000H Other : Error Response: At the time of a failure A3H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Command example: * Setting Brightness to 10 03H 10H 00H 00H 05H 00H FFH 00H 0AH 00H 21H * Setting Brightness to -10 03H 10H 00H 00H 05H 00H FFH 00H F6H FFH 0CH 030-2. VOLUME ADJUST ********************************************************************** Function: This command sets the volume. Command: 03H 10H 00H 00H 05H DATA01 .. DATA05 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 05H fixed DATA02 Setting items 00H : Volume 01H : Bass 02H : Treble 03H : Balance DATA03 Setting mode 00H : Absolute value specification 01H : Relative value specification DATA04 Setting Value ( Lower ranking 8 bits ) DATA05 Setting Value ( Upper ranking 8 bits ) Response: At the time of a success 23H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Results 0000H : Normal 0000H Other : Error Response: At the time of a failure A3H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Command example: * Setting Volume to "10" 03H 10H 00H 00H 05H 05H 00H 00H 0AH 00H 27H 030-4. IMAGE ADJUST ********************************************************************** Function: This command adjusts the Image. Command: 03H 10H 00H 00H 05H DATA01 .. DATA05 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Adjustment items +--------+--------+-------------------------+ | DATA01 | DATA02 | Adjustment items | +--------+--------+-------------------------+ | 08H | 00H | Position H | | 08H | 01H | Position V | | 09H | 00H | Pixel Adjust Clock | | 09H | 01H | Pixel Adjust Phase | +--------+--------+-------------------------+ DATA03 Adjustment mode 00H : Absolute value specification 01H : Relative value specification DATA04 Adjustment value ( Lower ranking 8 bits ) DATA05 Adjustment value ( Upper ranking 8 bits ) Response: At the time of a success 23H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Results 0000H : Normal 0000H Other : Error Response: At the time of a failure A3H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Command example: * Setting Position H to -10 03H 10H 00H 00H 05H 08H 00H 00H F6H FFH 15H 030-5. COLOR TEMPERATURE ADJUST ********************************************************************** Function: This command adjusts the Color Temperature. Command: 03H 10H 00H 00H 05H DATA01 .. DATA05 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 13H fixed DATA02 FFH fixed DATA03 Adjustment mode 00H : Absolute value specification 01H : Relative value specification DATA04 Adjustment value ( Lower ranking 8 bits ) DATA05 Adjustment value ( Upper ranking 8 bits ) Response: At the time of a success 23H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Results 0000H : Normal 0000H Other : Error Response: At the time of a failure A3H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Command example: * Setting Color Temperature to 3 03H 10H 00H 00H 05H 13H FFH 00H 03H 00H 2DH (!) Method of Specifying the Absolute Value of Special Adjustment Values V300/M402 +---------------------------+--------+--------+ | | DATA04 | DATA05 | +---------------------------+--------+--------+ | 5000K | 00H | 00H | | 6500K | 01H | 00H | | 7800K | 02H | 00H | | 9300K | 03H | 00H | +---------------------------+--------+--------+ NP61s/NP64s/NP4000s/NP215s +---------------------------+--------+--------+ | | DATA04 | DATA05 | +---------------------------+--------+--------+ | 5000K | 00H | 00H | | 6500K | 01H | 00H | | 7800K | 02H | 00H | | 8500K | 03H | 00H | | 9300K | 04H | 00H | | 10500K | 05H | 00H | +---------------------------+--------+--------+ 030-6. WHITE BALANCE ADJUST ********************************************************************** Function: This command adjusts the White Balance. Command: 03H 10H 00H 00H 05H DATA01 .. DATA05 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 14H fixed DATA02 Adjustment items 00H : Brightness R 01H : Brightness G 02H : Brightness B 03H : Contrast R 04H : Contrast G 05H : Contrast B DATA03 Adjustment mode 00H : Absolute value specification 01H : Relative value specification DATA04 Adjustment value ( Lower ranking 8 bits ) DATA05 Adjustment value ( Upper ranking 8 bits ) Response: At the time of a success 23H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Results 0000H : Normal 0000H Other : Error Response: At the time of a failure A3H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Command example: * Setting Brightness R to 10 03H 10H 00H 00H 05H 14H 00H 00H 0AH 00H 36H * Setting Brightness R to -10 03H 10H 00H 00H 05H 14H 00H 00H F6H FFH 21H 030-8. KEYSTONE ADJUST ********************************************************************** Function: This command adjusts the Keystone. Command: 03H 10H 00H 00H 05H DATA01 .. DATA05 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 15H fixed DATA02 Adjustment items 00H : H (!) 01H : V DATA03 Adjustment mode 00H : Absolute value specification 01H : Relative value specification DATA04 Adjustment value ( Lower ranking 8 bits ) DATA05 Adjustment value ( Upper ranking 8 bits ) Response: At the time of a success 23H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Results 0000H : Normal 0000H Other : Error Response: At the time of a failure A3H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Command example: * Setting Keystone H to 10 03H 10H 00H 00H 05H 15H 00H 00H 0AH 00H 37H * Setting Keystone H to -10 03H 10H 00H 00H 05H 15H 00H 00H F6H FFH 22H (!) NP4000,NP4100 Series 030-10. SIGNAL LEVEL ADJUST ********************************************************************** Function: This command adjusts the Signal Level. Command: 03H 10H 00H 00H 05H DATA01 .. DATA05 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Adjustment items +--------+--------+-----------------------------+ | DATA01 | DATA02 | Adjustment items | +--------+--------+-----------------------------+ | 2FH | 00H | R/G/B Gain R | | 2FH | 01H | R/G/B Gain G | | 2FH | 02H | R/G/B Gain B | +--------+--------+-----------------------------+ DATA03 Adjustment mode 00H : Absolute value specification 01H : Relative value specification DATA04 Adjustment value ( Lower ranking 8 bits ) DATA05 Adjustment value ( Upper ranking 8 bits ) Response: At the time of a success 23H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Results 0000H : Normal 0000H Other : Error Response: At the time of a failure A3H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Command example: * Setting Signal Level R/G/B Gain to 10 03H 10H 00H 00H 05H 2FH 00H 00H 0AH 00H 51H 030-11. VIDEO MODE ADJUST ********************************************************************** Function: This command adjusts the Video Mode. Command: 03H 10H 00H 00H 05H DATA01 .. DATA05 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Adjustment items +--------+--------+-------------------------+ | DATA01 | DATA02 | Adjustment items | +--------+--------+-------------------------+ | 16H | FFH | Gamma (!) | | 1AH | FFH | Noise Reduction Lumi (!)| | 1CH | FFH | Select Color Matrix (!) | | 22H | 00H | Telecine (!) | +--------+--------+-------------------------+ DATA03 Adjustment mode 00H : Absolute value specification 01H : Relative value specification DATA04 Adjustment value ( Lower ranking 8 bits ) DATA05 Adjustment value ( Upper ranking 8 bits ) Response: At the time of a success 23H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Results 0000H : Normal 0000H Other : Error Response: At the time of a failure A3H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Command example: * Setting Gamma to Black Detail 03H 10H 00H 00H 05H 16H FFH 00H 02H 00H 2FH (!) Method of Specifying the Absolute Value of Special Adjustment Values +---------------------------+--------+--------+ | | DATA04 | DATA05 | +---------------------------+--------+--------+ | Gamma Dynamic | 00H | 00H | | Gamma Natural | 01H | 00H | | Gamma Black Detail | 02H | 00H | | Noise Reduction Off | 00H | 00H | | Noise Reduction Low | 01H | 00H | | Noise Reduction Medium | 02H | 00H | | Noise Reduction High | 03H | 00H | | Select Color Matrix HDTV | 00H | 00H | | Select Color Matrix SDTV | 01H | 00H | | Select Color Matrix RGB | 02H | 00H | | Select Color Matrix AUTO | 03H | 00H | | Telecine Off | 00H | 00H | | Telecine 2-2/2-3 Auto | 01H | 00H | | Telecine 2-2 On | 02H | 00H | | Telecine 2-3 On | 03H | 00H | +---------------------------+--------+--------+ 030-12. IMAGE MODE ADJUST ********************************************************************** Function: This command adjusts the Image Mode. Command: 03H 10H 00H 00H 05H DATA01 .. DATA05 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Adjustment items +--------+--------+---------------------------+ | DATA01 | DATA02 | Adjustment items | +--------+--------+---------------------------+ | 18H | 00H | Aspect Ratio Input (!1) | +--------+--------+---------------------------+ DATA03 Adjustment mode 00H : Absolute value specification 01H : Relative value specification DATA04 Adjustment value ( Lower ranking 8 bits ) DATA05 Adjustment value ( Upper ranking 8 bits ) Response: At the time of a success 23H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Results 0000H : Normal 0000H Other : Error Response: At the time of a failure A3H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Command example: * Setting the Aspect Ratio to Letter Box 03H 10H 00H 00H 05H 18H 00H 00H 01H 00H 31H (!1) Method of Specifying the Absolute Value of Special Adjustment Values NP4000s +---------------------------+--------+--------+ | | DATA04 | DATA05 | +---------------------------+--------+--------+ | Aspect Ratio 4:3 (Window) | 00H | 00H | | Aspect Ratio Letter Box | 01H | 00H | | Aspect Ratio 1.78:1(16:9) | 02H | 00H | | Aspect Ratio Crop/WideZoom| 03H | 00H | | Aspect Ratio 4:3 Fill | 04H | 00H | | Aspect Ratio Normal/Auto | 05H | 00H | | Aspect Ratio Full | 06H | 00H | | Aspect Ratio 16:10 | 0CH | 00H | | Aspect Ratio 15:9 | 0DH | 00H | | Aspect Ratio Native | 0EH | 00H | +---------------------------+--------+--------+ NP61s/NP64s/NP215s/V300/VE282/M402 +----------------------------+--------+--------+-------+--------+------+ | | DATA04 | DATA05 | NP61s | NP64s | U300 | | | | | | NP215s | PE401| | | | | | V300 | | | | | | | VE282 | | | | | | | M402 | | +----------------------------+--------+--------+-------+--------+------+ | Aspect Ratio Normal / Auto | 00H | 00H | * | * | * | | Aspect Ratio Wide Zoom | 01H | 00H | * | *(!2)| x | | Aspect Ratio Cinema / 16:9 | 02H | 00H | * | * | * | | Aspect Ratio Native | 03H | 00H | * | * | * | | Aspect Ratio 4:3 | 04H | 00H | x | * | * | | Aspect Ratio 15:9 | 05H | 00H | x | * | * | | Aspect Ratio 16:10 | 06H | 00H | x | * | * | | Aspect Ratio Letter Box | 07H | 00H | x | *(!3)| x | | Aspect Ratio 5:4 | 08H | 00H | x | x | * | +----------------------------+--------+--------+-------+--------+------+ * : Supported x : Not supported (!2)Except NP-V300W/NP-V260W (!3NP-V300W/NP-V260W only 030-15. OTHER ADJUST ********************************************************************** Function: This command adjusts the various gains. Command: 03H 10H 00H 00H 05H DATA01 .. DATA05 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Adjustment items +--------+--------+------------------------------+ | DATA01 | DATA02 | Adjustment items | +--------+--------+------------------------------+ | 3BH | FFH | Overscan (!) | | 53H | FFH | Picture Management(!) | | 59H | FFH | Base Setting / Reference (!) | | 97H | FFH | Wall Color (!) | | 9FH | 00H | Dynamic Contrast(!) | +--------+--------+------------------------------+ DATA03 Adjustment mode 00H : Absolute value specification 01H : Relative value specification DATA04 Adjustment value ( Lower ranking 8 bits ) DATA05 Adjustment value ( Upper ranking 8 bits ) Response: At the time of a success 23H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Results 0000H : Normal 0000H Other : Error Response: At the time of a failure A3H 10H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Command example: * Setting Overscan to 10% 03H 10H 00H 00H 05H 3BH FFH 00H 02H 00H 54H (!) Method of Specifying the Absolute Value of Special Adjustment Values +-----------------------------+--------+--------+ | | DATA04 | DATA05 | +-----------------------------+--------+--------+ | Overscan 0% | 00H | 00H | | Overscan 5% | 01H | 00H | | Overscan 10% | 02H | 00H | | Overscan 25% | 03H | 00H | | Picture Management 1 | 00H | 00H | | Picture Management 2 | 01H | 00H | | Picture Management 3 | 02H | 00H | | Picture Management 4 | 03H | 00H | | Picture Management 5 | 04H | 00H | | Picture Management 6 | 05H | 00H | | Reference High-Bright | 00H | 00H | | Reference Presentation | 01H | 00H | | Reference Video | 02H | 00H | | Reference Movie | 03H | 00H | | Reference Graphic | 04H | 00H | | Reference sRGB | 05H | 00H | | Wall Color Off | 00H | 00H | | Wall Color Light blue | 01H | 00H | | Wall Color Pink | 02H | 00H | | Wall Color Light rose | 03H | 00H | | Wall Color Light yellow | 04H | 00H | | Wall Color Light green | 05H | 00H | | Wall Color Sky blue | 06H | 00H | | Wall Color Blackboard | 07H | 00H | | Wall Color Blackboard(Gray) | 08H | 00H | | Wall Color Whiteboard | 09H | 00H | | Dynamic Contrast Off | 00H | 00H | | Dynamic Contrast On | 01H | 00H | +-----------------------------+--------+--------+ 037. INFORMATION REQUEST ********************************************************************** Function: This command acquires the projector information. Command: 03H 8AH 00H 00H 00H 8DH Response: At the time of a success 23H 8AH 01H xxH 62H DATA01 .. DATA98 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 49 Projector name (!!) DATA50 .. 82 Reserved DATA83 .. 86 Lamp Hour Meter (second) (!) DATA87 .. 90 Filter Usage (second) DATA91 .. 94 Reserved DATA95 .. 98 Projector Usage (second) Response: At the time of a failure A3H 8AH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: (!) Lamp Hour Meter This is the timer for normal lamp mode conversion. (!!) NP4000/4001, NP4100/4100W, NP215, NP216 only Lamp Timer Acquisition Examples DATA83 DATA84 DATA85 DATA86 : Lamp Timer 00H 00H 00H 00H : Total 0 seconds C0H 65H 52H 00H : Total 5400000 seconds = 1500 hours 00H E4H 57H 00H : Total 5760000 seconds = 1600 hours * The projector's hours of use is displayed in terms of Normal mode values. It is also displayed with truncated a number after decimal point. 037-1. LAMP INFORMATION REQUEST ********************************************************************** Function: This command acquires the lamp information (in terms of Normal mode values) of projector. Command: 03H 8CH 00H 00H 00H 8FH Response: At the time of a success 23H 8CH 01H xxH 10H DATA01 .. DATA16 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 04 Lamp Hour Meter(Normal mode) (second) DATA05 .. 08 Reserved DATA09 .. 12 Lamp Use Warning Starting Time(Normal mode) (second) DATA13 .. 16 Lamp Use Prohibited Time(Normal mode) (second) Response: At the time of a failure A3H 8CH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: Example for acquiring remaining lamp time (in terms of Normal mode values) : Lamp Hour Meter (Normal mode) DATA01 DATA02 DATA03 DATA04 30H 2AH 00H 00H : 10800 second : Starting time for lamp usage warning message (in terms of Normal mode values) DATA09 DATA10 DATA11 DATA12 00H DDH 6DH 00H : 7200000 second Lamp remaining time (in terms of Normal mode values) = (7200000 - 10800) / 3600 = 1997 hour 037-2. LAMP INFORMATION REQUEST 2 ********************************************************************** Function: This command acquires lamp remaining amount. Command: 03H 94H 00H 00H 00H 97H Response: At the time of a success 23H 94H 01H xxH 05H DATA01 .. DATA05 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 04 Reserved DATA05 lamp remaining amount (100% to -10%) Response: At the time of a failure A3H 94H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 037-4. LAMP INFORMATION REQUEST 3 ********************************************************************** Function: This command acquires the information on the projector lamp. Command: 03H 96H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 Target 00H : Lamp1 01H : Lamp2 DATA02 Item 00H : Lamp Hour Meter (second)(!3) 01H : Lamp usage time (second)(!4) 04H : lamp remaining amount until lamp warning message ( 100% to -X%(!2) ) 05H : Lamp usage time (Normal mode)(second)(!5) 06H : Lamp usage time (Eco mode)(second)(!5) 08H : Remaining time until lamp warning message starts to appear (in terms of specified values) 09H : Remaining time until lamp warning message starts to appear (in terms of Normal mode values) 0AH : Remaining time until lamp warning message starts to appear (in terms of Eco mode values) 10H : Remaining time until inhibition of lamp usage (in terms of specified values) 11H : Remaining time until inhibition of lamp usage (in terms of Normal mode values) 12H : Remaining time until inhibition of lamp usage (in terms of Eco mode values) Response: At the time of a success 23H 96H 01H xxH 06H DATA01 to DATA06 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 same values as DATA01 of the command DATA02 same values as DATA02 of the command DATA03 to 06 Acquired information(!1) Response: At the time of a failure A3H 96H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: * In case of acquiring lamp's use of hours 03H 96H 00H 00H 02H 00H 01H 9CH Example of acquisition DATA03 DATA04 DATA05 DATA06 : lamp's use of hours 50H 46H 00H 00H : 18000 seconds Lamp Usage = 18000 / 3600 = 5 hour * In case of acquiring the remaining time until lamp warning message starts to appear (in terms of specified values) 03H 96H 00H 00H 02H 00H 08H A3H Example of acquisition DATA03 DATA04 DATA05 DATA06 : Remaining time 40H 7EH 05H 00H : 360000 seconds Remaining time until lamp warning message starts to appear = 360000/ 3600 = 100 hours (!1) If "time" is specifed for "Options for acquisition", values in seconds will be returned. (!2) X = 100 - ((Lamp Use Prohibited Time * 100) / Lamp Use Warning Starting Time) Example) The case of Lamp Use Prohibited Time 2100[H]�A Lamp Use Warning Starting Time 2000[H] Model. X = 100 - ((2100 * 100) / 2000) = -5[%] (!3) Lamp Hour Meter This is the timer for normal lamp mode conversion. (!4) Lamp usage time This is the lamp total usage. It is displayed in the projector's menu. (!5) NP4000/4001, NP4100/4100W : This function is not supported. 037-5. TEMP INFORMATION REQUEST ********************************************************************** Function: This command acquires the information about temperature inside the projector. Command 03H 99H 00H 00H 01H DATA01 CKS (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 Target sensor 00H : Intake (outside air) temperature 01H : Lamp (inside air) temperature (!) 02H or later reserved (allocated sequentially to each model) Response: At the time of a success 23H 99H 01H xxH 05H DATA01 .. DATA05 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 Setting Items ( Same as DATA01 of the transmit data ) DATA02 .. 05 Temperature information (long type unit: 0.1 degree Celsius/32.18 degrees Fahrenheit: 0 degree Celsius/32 degrees Fahrenheit or less will be returned as 0 degree Celsius/32 degrees Fahrenheit) Response: At the time of a failure A3H 99H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: Example for Temp DATA02 DATA03 DATA04 DATA05 CBH 01H 00H 00H : 45.9 degrees Celsius/ 114.6 degrees Fahrenheit (!) NP61, NP64 Series only 037-6. CARBON SAVINGS INFORMATION REQUEST ********************************************************************** Function: This command acquires the Carbon Saving values on the projector. Command: 03H 9AH 00H 00H 01H DATA01 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Acquirement items 00H : Total Carbon Savings 01H : Carbon Savings during operation Response: At the time of a success 23H 9AH 01H xxH 09H DATA01 to DATA09 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Same as DATA01 of the transmit data DATA02 to 05 Carbon Savings (Kilogram Maximum: 99999[kg]) DATA06 to 09 Carbon Savings (Milligram Maximum:999999[mg]) Response: At the time of a failure A3H 9AH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: Example for Total Carbon Savings DATA02 DATA03 DATA04 DATA05 : Kilogram 9CH 09H 00H 00H : 2460 [kg] DATA06 DATA07 DATA08 DATA09 : Milligram 06H F9H 00H 00H : 63750 [mg] Total Carbon Savings = (2460 * 1000) + (63750 / 1000) = 2460063.75 [g] = 2460 + (63750 / 1000 / 1000) = 2460.06375 [kg] 037-7. LAMP INFORMATION REQUEST 4 ********************************************************************** Function: This command acquires the information on the projector lamp. Command: 03H 9BH 00H 00H 03H DATA01 DATA02 DATA03 CKS (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 Target 00H : Lamp1 01H : Lamp2 DATA02 Unit(!4) 00H : Second 01H : Reserved 02H : Hour DATA03 Item 00H : Lamp Hour Meter (second)(!2) 01H : Lamp usage time (second)(!3) 04H : lamp remaining amount until lamp warning message ( 100% to -X%(!1) ) 05H : Lamp usage time (Normal mode)(second) (!5) 06H : Lamp usage time (Eco mode)(second) (!5) 08H : Remaining time until lamp warning message starts to appear (in terms of specified values) 09H : Remaining time until lamp warning message starts to appear (in terms of Normal mode values) 0AH : Remaining time until lamp warning message starts to appear (in terms of Eco mode values) 10H : Remaining time until inhibition of lamp usage (in terms of specified values) 11H : Remaining time until inhibition of lamp usage (in terms of Normal mode values) 12H : Remaining time until inhibition of lamp usage (in terms of Eco mode values) Response: At the time of a success 23H 9BH 01H xxH 07H DATA01 to DATA07 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 same values as DATA01 of the command DATA02 same values as DATA02 of the command DATA03 same values as DATA03 of the command DATA04 to 07 Acquired information Response: At the time of a failure A3H 9BH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: * In case of acquiring lamp's use of hours 03H 9BH 00H 00H 03H 00H 00H 01H CKS Example of acquisition DATA04 DATA05 DATA06 DATA07 : lamp's use of hours 50H 46H 00H 00H : 18000 seconds Lamp Usage = 18000 / 3600 = 5 hour (!1) X = 100 - ((Lamp Use Prohibited Time * 100) / Lamp Use Warning Starting Time) Example) The case of Lamp Use Prohibited Time 2100[H]�A Lamp Use Warning Starting Time 2000[H] Model. X = 100 - ((2100 * 100) / 2000) = -5[%] (!2) Lamp Hour Meter This is the timer for normal lamp mode conversion. (!3) Lamp usage time This is the lamp total usage. It is displayed in the projector's menu. (!4) This setting is ignored, if the Item's unit is not time. (!5) NP4000/4001, NP4100/4100W : This function is not supported. 050. REMOTE KEY CODE ********************************************************************** Function: This command sends remote control key codes of projector. Command: 02H 0FH 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Remote control key code (Word type) Key number DATA01 DATA02 Key name -------------------------------------------- 2 02H 00H POWER ON 3 03H 00H POWER OFF 4 04H 00H SOURCE (AUTO) 5 05H 00H AUTO 6 06H 00H MENU 7 07H 00H UP 8 08H 00H DOWN 9 09H 00H RIGHT 10 0AH 00H LEFT 11 0BH 00H ENTER 12 0CH 00H CANCEL 13 0DH 00H HELP 19 13H 00H MUTE 71 47H 00H PICMUTE ON 72 48H 00H PICMUTE OFF 73 49H 00H SNDMUTE ON 74 4AH 00H SNDMUTE OFF 75 4BH 00H RGB1(*5) 76 4CH 00H RGB2(*5) 79 4FH 00H VIDEO1 81 51H 00H S-VIDEO1 85 55H 00H VIEWER 132 84H 00H VOLUME UP 133 85H 00H VOLUME DOWN 134 86H 00H KEYSTONE UP 135 87H 00H KEYSTONE DOWN 138 8AH 00H FREEZE 163 A3H 00H ASPECT 215 D7H 00H SEQSOURCE(source select) 216 D8H 00H RGB TOGGLE 217 D9H 00H VIDEO TOGGLE 223 DFH 00H PICTURE MANAGEMENT 225 E1H 00H COMPONENT 228 E4H 00H DVI/DVI(DIGITAL) 229 E5H 00H LAN 261 05H 01H HDMI 263 07H 01H FOCUS/ZOOM 269 0DH 01H HDMI2 Response: At the time of a success 22H 0FH 01H xxH 01H DATA01 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Results 00H : Normal FFH : Error Response: At the time of a failure A2H 0FH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Command example: * Sending the AUTO key code 02H 0FH 00H 00H 02H 05H 00H 18H 053. LENS CONTROL ********************************************************************** Function: This command controls the lens. (Time specification) Command: 02H 18H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Target 00H : Zoom 01H : Focus 02H : Lens Shift (H) 03H : Lens Shift (V) DATA02 Contents 00H : Stops 01H : Drives for 1 second in the direction of plus 02H : Drives for 0.5 second in the direction of plus 03H : Drives for 0.25 second in the direction of plus FDH : Drives for 0.25 second in the direction of minus FEH : Drives for 0.5 second in the direction of minus FFH : Drives for 1 second in the direction of minus Response: At the time of a success 22H 18H 01H xxH 01H DATA01 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Results 00H : Normal 01H : Error Response: At the time of a failure A2H 18H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: While the lens is being driven, the same command can be issued for control purposes without causing a stop. 058. FORCED ONSCREEN MUTE SET ********************************************************************** Function: This command controls the mute of forced on-screen. Command: 02H 19H 00H 00H 01H DATA01 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Setting Value 00H : OFF 01H : ON Response: At the time of a success 22H 19H 01H xxH 01H DATA01 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Results 00H : Normal 01H : Error Response: At the time of a failure A2H 19H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 060. GAIN PARAMETER REQUEST 2 ********************************************************************** Function: This command acquires the adjustment values. Command: 03H 04H 00H 00H 03H DATA01 .. DATA03 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Acquirement items (!) DATA03 00H fixed Response: At the time of a success 23H 04H 01H xxH 0DH DATA01 .. DATA13 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Adjustment status 00H : Displaying impossible 01H : Adjustment impossible 02H : Adjustment possible FFH : Selected gain is not available. DATA02 Maximum adjustment value ( Lower ranking 8 bits ) DATA03 Maximum adjustment value ( Upper ranking 8 bits ) DATA04 Minimum adjustment value ( Lower ranking 8 bits ) DATA05 Minimum adjustment value ( Upper ranking 8 bits ) DATA06 Default adjustment value ( Lower ranking 8 bits ) DATA07 Default adjustment value ( Upper ranking 8 bits ) DATA08 Current value ( Lower ranking 8 bits ) DATA09 Current value ( Upper ranking 8 bits ) DATA10 .. 13 Reserved Response: At the time of a failure A3H 04H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) (!) Acquirement items +--------+--------+--------------------------------------+---------+-------+--------+------+-------+ | DATA01 | DATA02 | Acquirement name | NP4000s | NP61s | NP215s | U300 | VE282 | | | | | | NP64s | V300 | PE401| | | | | | | | M402 | | | +--------+--------+--------------------------------------+---------+-------+--------+------+-------+ | 00H | 00H | Picture / Brightness | * | * | * | * | * | | 01H | 00H | Picture / Contrast | * | * | * | * | * | | 02H | 00H | Picture / Color | * | * | * | * | * | | 03H | 00H | Picture / Hue | * | * | * | * | * | | 04H | 00H | Picture / Sharpness | * | * | * | * | * | | 05H | 00H | Volume | * | * | * | * | * | | 13H | 00H | Color Temperature | * | * | * | x | x | | 14H | 00H | White Balance / Brightness R | * | x | x | x | x | | 14H | 01H | White Balance / Brightness G | * | x | x | x | x | | 14H | 02H | White Balance / Brightness B | * | x | x | x | x | | 14H | 03H | White Balance / Contrast R | * | x | x | x | x | | 14H | 04H | White Balance / Contrast G | * | x | x | x | x | | 14H | 05H | White Balance / Contrast B | * | x | x | x | x | | 15H | 01H | Keystone / V | x | * | * | x | * | | 16H | 00H | Gamma | x | * | * | * | * | | 18H | 00H | Aspect Ratio / Input Signal | x | * | * | x | * | | 1AH | 00H | Noise Reduction(Luminance) | x | * | * | x | * | | 22H | 00H | Telecine | x | * | * | x | x | | 53H | 00H | Picture Management | x | * | * | * | * | | 59H | 00H | Base Setting | x | * | * | x | x | | 97H | 00H | Wall Color | x | * | * | * | * | | 9FH | 00H | Dynamic Contrast | x | x | * | x | * | +--------+--------+--------------------------------------+---------+-------+--------+------+-------+ * : Supported x : Not supported Command example: * In case of acquiring Picture Brightness 03H 04H 00H 00H 03H 00H 00H 00H 0AH 061. LAMP COOLING TIME REQUEST ********************************************************************** Function: This command acquires lamp cooling time. Command: 03H 8DH 00H 00H 00H 90H Response: At the time of a success 23H 8DH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Lower ranking 8 bits of cooling time(unit: second) (!) DATA02 Upper ranking 8 bits of cooling time(unit: second) (!) Response: At the time of a failure A3H 8DH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: (!) Example of acquisition of cooling time DATA01 DATA02 Time 3CH 00H : 60 Second 077. MUTE CONTROL ********************************************************************** Function: This command controls the mute of picture, sound and on-screen. Command: 02H 1AH 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Setting items 00H : Image(Picture) 01H : Sound 02H : On-Screen DATA02 Setting Value 00H : OFF 01H : ON Response: At the time of a success 22H 1AH 01H xxH 01H DATA01 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Results 00H : Normal 01H : Error Response: At the time of a failure A2H 1AH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: * Sound mute is cancelled in the following cases: Input connector switching Video signal switching Volume adjustment 078-1. SETTING REQUEST ********************************************************************** Function: This command acquires the function information of projector. Command: 00H 85H 00H 00H 01H 00H 86H Response: At the time of a success 20H 85H 01H xxH 20H DATA01 .. DATA32 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 03 Projector type +--------+--------+--------+-------------------+ | DATA01 | DATA02 | DATA03 | | +--------+--------+--------+-------------------+ | 08H | 00H | 07H | NP4000 | | 08H | 00H | 10H | NP4100 | | 08H | 01H | 10H | NP4100W | | 11H | 00H | 00H | NP41/61 | | 11H | 01H | 00H | NP52/62 | | 11H | 00H | 12H | NP64 | | 11H | 01H | 12H | NP54 | | 11H | 02H | 12H | NP63 | | 11H | 03H | 12H | NP43 | | 11H | 04H | 12H | NP53 | | 11H | 00H | 11H | NP215 | | 11H | 01H | 11H | NP210 | | 11H | 02H | 11H | NP115 | | 11H | 03H | 11H | NP110 | | 11H | 04H | 11H | NP216 | | 14H | 01H | 10H | NP-U250X | | 14H | 02H | 10H | NP-U300X | | 14H | 03H | 10H | NP-U260W | | 14H | 04H | 10H | NP-U310W | | 14H | 00H | 11H | NP-PE401H | | 16H | 00H | 10H | NP-V300X | | 16H | 01H | 10H | NP-V260X | | 16H | 02H | 10H | NP-V230X | | 16H | 03H | 10H | NP-V260 | | 16H | 04H | 10H | NP-V230 | | 16H | 05H | 10H | NP-V300W | | 16H | 06H | 10H | NP-V260W | | 16H | 07H | 10H | NP-V260R | | 16H | 00H | 11H | NP-VE282X | | 16H | 01H | 11H | NP-VE281X | | 16H | 02H | 11H | NP-VE280X | | 16H | 03H | 11H | NP-VE282 | | 16H | 04H | 11H | NP-VE281 | | 16H | 05H | 11H | NP-VE280 | | 22H | 00H | 10H | NP-M402X | | 22H | 01H | 10H | NP-M362X | | 22H | 02H | 10H | NP-M322X | | 22H | 03H | 10H | NP-M282X | | 22H | 04H | 10H | NP-M402W | | 22H | 05H | 10H | NP-M362W | | 22H | 06H | 10H | NP-M322W | | 22H | 07H | 10H | NP-M332XS | | 22H | 08H | 10H | NP-M352WS | | 22H | 09H | 10H | NP-M302WS | +--------+--------+--------+-------------------+ DATA04 Sound function 00H : Not available 01H : Available DATA05 Calender function 00H : No function 01H or 03H : Timer function, sleep timer function 02H : Sleep timer function DATA06 .. 32 Reserved Response: At the time of a failure A0H 85H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 078-2. RUNNING STATUS REQUEST ********************************************************************** Function: This command acquires the status of the projector operation. Command: 00H 85H 00H 00H 01H 01H 87H Response: At the time of a success 20H 85H 01H xxH 10H DATA01 .. DATA16 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Reserved DATA03 Projector status 00H : Idling 01H : Power On DATA04 Cooling processing 00H : No execution(Normal condition) 01H : During execution DATA05 Power On/Off processing 00H : No execution(Normal condition) 01H : During execution DATA06 Status of operation 00H : Idling 04H : Power On 05H : Cooling 06H : Idling(Error occurrence) Other than above : (nondisclosure) internal use of code during a state transition period DATA07 PC Card insertion 00H : Not inserted 01H : Inserted DATA08 USB Mouse connection 00H : Not connected 01H : Connected DATA09 .. 16 Reserved Response: At the time of a failure A0H 85H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 078-3. INPUT STATUS REQUEST ********************************************************************** Function: This command acquires the status of input signal of the projector. Command: 00H 85H 00H 00H 01H 02H 88H Response: At the time of a success 20H 85H 01H xxH 10H DATA01 .. DATA16 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Selecting signal processing 00H : No execution(Normal condition) 01H : During execution DATA02 Signal number( Entry list number - 1 ) 0 .. 199 DATA03 .. 04 Selected input terminal +--------------------------+--------+--------+ | Terminal name | DATA03 | DATA04 | +--------------------------+--------+--------+ | Computer1 | 01H | 01H | | Computer2 | 02H | 01H | | Computer3(DVI)/HDMI/HDMI1| 01H | 06H | | HDMI2 | 02H | 06H | | Component | 03H | 04H | | Video | 01H | 02H | | S-Video | 01H | 03H | | USB-A(Viewer) | 01H | 07H | | LAN | 02H | 07H | | USB-B | 04H | 07H | +--------------------------+--------+--------+ DATA05 Entry list type 01H : Default 02H : User DATA06 Test pattern display 00H : No display(Normal condition) 01H : Displaying DATA07 ..08 Reserved DATA09 Indicate Contents 00H = Picture signal displaying 01H = No signal 02H = Viewer displaying 03H = Test pattern displaying 04H = LAN displaying DATA10 .. 16 Reserved Response: At the time of a failure A0H 85H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 078-4. MUTE STATUS REQUEST ********************************************************************** Function: This command acquires the status of the mute of projector. Command: 00H 85H 00H 00H 01H 03H 89H Response: At the time of a success 20H 85H 01H xxH 10H DATA01 .. DATA16 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Picture mute 00H : OFF 01H : ON DATA02 Sound mute 00H : OFF 01H : ON DATA03 On-screen mute 00H : OFF 01H : ON DATA04 Forced on-screen mute 00H : OFF 01H : ON DATA05 On-screen display 00H : No display 01H : Displaying DATA06 .. 16 Reserved Response: At the time of a failure A0H 85H ID xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 078-5. MODEL NAME REQUEST ********************************************************************** Function: This command acquires the model name of the projector. Command: 00H 85H 00H 00H 01H 04H 8AH Response: At the time of a success 20H 85H 01H xxH 20H DATA01 .. DATA32 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 32 Model name (NULL termination character string) Response: At the time of a failure A0H 85H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 078-6. COVER STATUS REQUEST ********************************************************************** Function: This command acquires the status of lens cover of the projector. Command: 00H 85H 00H 00H 01H 05H 8BH Response: At the time of a success 20H 85H 01H xxH 01H DATA01 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 Status 00H : Normal 01H : Cover Close Response: At the time of a failure A0H 85H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 079. FREEZE CONTROL ********************************************************************** Function: This command controls the freeze. Command: 01H 98H 00H 00H 01H DATA01 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 Operation types 00H : Reserved 01H : Freeze start 02H : Freeze cancel Response: At the time of a success 21H 98H 01H xxH 01H DATA01 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 Results 00H : Normal 01H : Error Response: At the time of a failure A1H 98H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: 084. INFORMATION STRING REQUEST ********************************************************************** Function: This command acquires information character string displayed from projector. Command: 00H D0H 00H 00H 03H DATA01 to DATA03 CKS (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 Resource language selection 00H : English fixed DATA02 Classification by information type (!1) DATA03 Selection for character string to be acquired 01H : Acquisition of information character string Response: At the time of a success 20H D0H 01H xxH ??H DATA01 to DATA?? CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 Classification by information type (!1) ( Same as DATA02 of the transmit data ) DATA02 Character string types ( Same as DATA03 of the transmit data ) DATA03 String length of label / information ( not including NULL character ) DATA04 to DATAxx Character string of label / information ( NULL termination character string ) Response: At the time of a failure A0H D0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: (!1)Information type Number Title Description ----------------------------------------------------------------- 3 (03H) Horizontal Frequency 4 (04H) Vertical Frequency 091. DIGITAL ZOOM REQUEST ********************************************************************** Function: This command acquires the digital zoom( Magnify ) information. Command: 03H 20H 00H 00H 00H 23H Response: At the time of a success 23H 20H 01H xxH 20H DATA01 .. DATA32 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 .. 02 Digital Zoom adjustment value (short type) (!) DATA03 .. 04 Maximum value of Digital Zoom adjustment range (short type) (!) DATA05 .. 06 Minimum value of Digital Zoom adjustment range (short type) (!) DATA07 .. 32 Reserved Response: At the time of a failure A3H 20H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 092-2. DIGITAL ZOOM DATA SET ********************************************************************** Function: This command sets digital zoom. Command: 03H 21H 00H 00H 04H DATA01 .. DATA04 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 01H fixed DATA02 Setting mode 00H : Absolute value specification 01H : Relative value specification DATA03 Setting Value ( Lower ranking 8 bits ) DATA04 Setting Value ( Upper ranking 8 bits ) Response: At the time of a success 23H 21H 01H xxH 03H DATA01 .. DATA03 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 01H fixed DATA02 .. 03 Results 0000H : Normal 0000H Other : Error Response: At the time of a failure A3H 21H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-1. MENU MODE REQUEST ********************************************************************** Function: This command acquires the Menu Mode of the projector. Command: 03H B0H 00H 00H 01H 00H B4H Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 00H fixed DATA02 Setting Value 00H : Advanced Menu 01H : Basic Menu Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-2. LANGUAGE REQUEST ********************************************************************** Function: This command acquires the Language of the projector. Command: 03H B0H 00H 00H 01H 01H B5H Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 01H fixed DATA02 Setting Value 00H : English 01H : Japanese 02H : German 03H : French 04H : Italian 05H : Spanish 06H : Swedish 07H : Chinese 08H : Finnish 09H : Norwegian 0AH : Dutch 0BH : Turkish 0CH : Polish 0DH : Russian 0EH : Greek 0FH : Korean 10H : Hungarian 11H : Portuguese 12H : Czech 13H : Arabic 14H : Danish 15H : Romanian 16H : Croatian 17H : Bulgarian 18H : Indonesian 19H : Hindi 1AH : Thai 1BH : Chinese(Traditional) 1CH : Uyghur Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-3. MENU COLOR SELECT REQUEST ********************************************************************** Function: This command acquires Menu Color Select of the projector. Command: 03H B0H 00H 00H 01H 02H B6H Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 02H fixed DATA02 Setting Value 00H : Color 01H : Monochrome Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-5. DISPLAY TIME REQUEST ********************************************************************** Function: This command acquires the Display Time of the projector. Command: 03H B0H 00H 00H 01H 04H B8H Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 04H fixed DATA02 Setting Value 00H : Manual 01H : Auto 5 sec 02H : Auto 15 sec 03H : Auto 45 sec Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-7. MESSAGE REQUEST ********************************************************************** Function: This command acquires the setting of the message of projector. Command: 03H B0H 00H 00H 01H 06H BAH Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 06H fixed DATA02 Setting Value 00H : OFF 01H : ON Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-8. LAMP MODE REQUEST ********************************************************************** Function: This command acquires the setting of the lamp mode of projector. Command: 03H B0H 00H 00H 01H 07H BBH Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 07H fixed DATA02 Setting Value M402 +-------------+------------+ |Setting Value| DATA02 | +-------------+------------+ | 00H | Off | | 01H | Auto Eco | | 02H | Normal | | 03H | Eco | +-------------+------------+ NP4000s/NP61s/NP215s/NP64s/U300/VE282/PE401 +-------------+--------+ |Setting Value| DATA02 | +-------------+--------+ | 00H | Normal l | 01H | Eco | +-------------+--------+ Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-10. CLOSED CAPTION REQUEST ********************************************************************** Function: This command acquires the setting of the closed caption of projector. Command: 03H B0H 00H 00H 01H 09H BDH Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 09H fixed DATA02 Setting Value 00H : OFF 01H : Caption 1 02H : Caption 2 03H : Caption 3 04H : Caption 4 05H : Text 1 06H : Text 2 07H : Text 3 08H : Text 4 Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-11. ORIENTATION REQUEST ********************************************************************** Function: This command acquires the setting of the orientation of projector. Command: 03H B0H 00H 00H 01H 0AH BEH Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 0AH fixed DATA02 Setting Value 00H : Desktop Front 01H : Ceiling Rear 02H : Desktop Rear 03H : Ceiling Front Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-12. BACKGROUND REQUEST ********************************************************************** Function: This command acquires the setting of the background of projector. Command: 03H B0H 00H 00H 01H 0BH BFH Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 0BH fixed DATA02 Setting Value 00H : Blue 01H : Black 02H : Logo Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-23. AUTO START REQUEST ********************************************************************** Function: This command acquires the setting of the auto start of projector. Command: 03H B0H 00H 00H 01H 16H CAH Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 16H fixed DATA02 Setting Value 00H : OFF 01H : ON Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-24. POWER MANAGEMENT REQUEST ********************************************************************** Function: This command acquires the setting of the power management of projector. Command: 03H B0H 00H 00H 01H 17H CBH Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 17H : Power Management (!) DATA02 Setting Value +---------------+------------+ | Setting Value | DATA02 | +---------------+------------+ | 00H | OFF | | 01H | 0:05 | | 02H | 0:10 | | 03H | 0:20 | | 04H | 0:30 | +---------------+------------+ Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: (!) On the NP61,NP4100 series, "Power Management" has been changed to "Auto Power Off". 097-27. FAN MODE REQUEST ********************************************************************** Function: This command acquires the setting of the fan mode of projector. Command: 03H B0H 00H 00H 01H 1AH CEH Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 1AH fixed DATA02 Setting Value 00H : AUTO 01H : HIGH SPEED 02H : HIGH ALTITUDE Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-30. PANEL KEY LOCK REQUEST ********************************************************************** Function: This command acquires the setting of the control panel key lock of projector. Command: 03H B0H 00H 00H 01H 1DH D1H Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 1DH fixed DATA02 Setting Value 00H : Disable 01H : Enable Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-32. COMMUNICATION REQUEST ********************************************************************** Function: This command acquires the setting of the communication speed of projector. Command: 03H B0H 00H 00H 01H 1FH D3H Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 1FH fixed DATA02 Setting Value 00H : 4800bps 01H : 9600bps 02H : 19200bps 03H : 38400bps Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-33. DEFAULT SOURCE REQUEST ********************************************************************** Function: This command acquires the setting of the default source select of projector. Command: 03H B0H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 20H fixed DATA02 Acquisition Object 00H : Select 01H : Source Response: At the time of a success 23H B0H 01H xxH 03H DATA01 .. DATA03 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 20H fixed DATA02 .. 03 Setting Value +--------+--------+---------------------------------+ | DATA02 | DATA03 | Setting Value | +--------+--------+---------------------------------+ | 00H | 00H | Last | | 00H | 01H | Auto | | 00H | 02H | Select | | 01H | 00H | COMPUTER1 | | 01H | 01H | COMPUTER2 | | 01H | 02H | COMPUTER3 | | 01H | 03H | COMPONENT | | 01H | 04H | VIDEO | | 01H | 05H | S-VIDEO | +--------+--------+---------------------------------+ Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-34. PJ ID ENABLE REQUEST ********************************************************************** Function: This command acquires the setting of the projector id enable of projector. Command: 03H B0H 00H 00H 01H 21H D5H Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 21H fixed DATA02 Setting Value 00H : Disable 01H : Enable Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-35. PJ ID REQUEST ********************************************************************** Function: This command acquires the setting of the projector id of projector. Command: 03H B0H 00H 00H 01H 22H D6H Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 22H fixed DATA02 Setting Value Projector ID ( Control ID ) 1 .. 254 Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-39. TEST PATTERN REQUEST ********************************************************************** Function: This command acquires the setting of the test pattern of projector. Command: 03H B0H 00H 00H 01H 26H DAH Response: At the time of a success 23H B0H 01H xxH 04H DATA01 .. DATA04 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 26H fixed DATA02 .. 04 Test pattern ID +--------------------------+-----------------+ | Pattern ID | | +--------+--------+--------| Pattern Name | | DATA02 | DATA03 | DATA04 | | +--------+--------+--------+-----------------+ | 02H | 00H | 07H | Cross Hatch | | 04H | 00H | 07H | Raster(0%) | | 05H | 00H | 07H | Raster(25%) | | 06H | 00H | 07H | Raster(50%) | | 07H | 00H | 07H | Raster(100%) | | 07H | 00H | 01H | Raster Red | | 07H | 00H | 02H | Raster Green | | 07H | 00H | 04H | Raster Blue | | 19H | 00H | 04H | Blue Raster 60 | | 17H | 00H | 07H | Gray Raster 10 | | 0AH | 00H | 07H | Gray Raster 30 | | 20H | 00H | 07H | Ramp H | | 20H | 00H | 01H | Red Ramp H | | 21H | 00H | 07H | Ramp V | +--------+--------+--------+-----------------+ Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-88. LAMP SELECT REQUEST ********************************************************************** Function: This command acquires the setting of the Lamp Select of projector. Command: 03H B0H 00H 00H 01H 57H 0BH Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 57H fixed DATA02 Setting Value 00H : Dual 01H : Lamp1 02H : Lamp2 Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-89. LAMP INTERVAL REQUEST ********************************************************************** Function: This command acquires the setting of the Lamp Interval of projector. Command: 03H B0H 00H 00H 01H 58H 0CH Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 58H fixed DATA02 Setting Value 00H : Auto 01H : 1 week 02H : 4 weeks 07H : 2000H 09H : 12H 0AH : 24H Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-148. KEYSTONE SELECT REQUEST ********************************************************************** Function: This command acquires the setting of Keystone Select. Command: 03H B0H 00H 00H 01H 93H 47H Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 95H fixed DATA02 Setting Value 00H : Auto 01H : Manual Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-174. REMOTE SENSOR REQUEST ********************************************************************** Function: This command acquires the setting of Remote Sensor. Command: 03H B0H 00H 00H 01H ADH 61H Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 ADH fixed DATA02 Setting Value 00H : Front/Rear 01H : Front 02H : Rear Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-196. WXGA MODE SETTING REQUEST ********************************************************************** Function: This command acquires the setting of the WXGA Mode of projector. Command: 03H B0H 00H 00H 01H C3H 77H Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 C3H fixed DATA02 Setting Value 00H : OFF 01H : ON Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 097-239. 3D MODE REQUEST ********************************************************************** Function: This command acquires the setting of 3D mode for current selected terminal of the projector. Command: 03H B0H 00H 00H 01H DBH 8FH Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 DBH fixed DATA02 Setting Value 00H : Disable 01H : Enable Response: At the time of a failure A3H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: This command is available only when displaying an image. 097-240. DLP Link REQUEST ********************************************************************** Function: This command acquires the setting of DLP Link for current selected terminal of the projector. Command: 03H B0H 00H 00H 01H DCH 90H Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 DCH fixed DATA02 Setting Value 00H : Disable 01H : Enable Response: At the time of a failure A3H B0H 01H xxH 02H DATA1H DATA02 CKS (*1) (*2) (*4) (*3) Supplement: This command is available only when displaying an image. 097-241. 3D FORMAT REQUEST ********************************************************************** Function: This command acquires the setting of 3D format for current selected terminal of the projector. Command: 03H B0H 00H 00H 01H DDH 91H Response: At the time of a success 23H B0H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 DDH fixed DATA02 Setting Value V300/VE282/M402 +----------------------------+--------+-------+------+ | | DATA02 | V300 | M402 | | | | VE282 | | +----------------------------+--------+-------+------+ | Frame Sequential | 00H | * | * | | Top and Bottom (Over/Under)| 01H | * | * | | Side by Side | 02H | x | * | | Frame Packing | 03H | x | * | | Auto | 04H | x | * | +----------------------------+--------+-------+------+ Response: At the time of a failure A3H B0H 01H xxH 02H DATA1H DATA02 CKS (*1) (*2) (*4) (*3) Supplement: This command is available only when displaying an image. 098-1. MENU MODE SET ********************************************************************** Function: This command sets the menu mode of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 00H fixed DATA02 Setting Value 00H : Advanced Menu 01H : Basic Menu Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 00H fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-2. LANGUAGE SET ********************************************************************** Function: This command sets the language of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 01H fixed DATA02 Setting Value 00H : English 01H : Japanese 02H : German 03H : French 04H : Italian 05H : Spanish 06H : Swedish 07H : Chinese 08H : Finnish 09H : Norwegian 0AH : Dutch 0BH : Turkish 0CH : Polish 0DH : Russian 0EH : Greek 0FH : Korean 10H : Hungarian 11H : Portuguese 12H : Czech 13H : Arabic 14H : Danish 15H : Romanian 16H : Croatian 17H : Bulgarian 18H : Indonesian 19H : Hindi 1AH : Thai 1BH : Chinese(Traditional) 1CH : Uyghur Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 01H fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-3. MENU COLOR SELECT SET ********************************************************************** Function: This command sets the menu color select of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 02H fixed DATA02 Setting Value 00H : Color 01H : Monochrome Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 02H fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-5. DISPLAY TIME SET ********************************************************************** Function: This command sets the display time of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 04H fixed DATA02 Setting Value 00H : Manual 01H : Auto 5 sec 02H : Auto 15 sec 03H : Auto 45 sec Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 04H fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-7. MESSAGE SET ********************************************************************** Function: This command sets the message of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 06H fixed DATA02 Setting Value 00H : OFF 01H : ON Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 06H fixed DATA02 Results 00H : Normal 01H : Error A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-8. LAMP MODE SET ********************************************************************** Function: This command sets the lamp mode of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 07H fixed DATA02 Setting Value M402 +-------------+------------+ |Setting Value| DATA02 | +-------------+------------+ | 00H | Off | | 01H | Auto Eco | | 02H | Normal | | 03H | Eco | +-------------+------------+ NP60s/NP4000s/NP61s/NP215s/NP64s/U300/VE282/PE401 +-------------+--------+ |Setting Value| DATA02 | +-------------+--------+ | 00H | Normal l | 01H | Eco | +-------------+--------+ Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 07H fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-10. CLOSED CAPTION SET ********************************************************************** Function: This command sets the closed caption of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 09H fixed DATA02 Setting Value 00H : OFF 01H : Caption 1 02H : Caption 2 03H : Caption 3 04H : Caption 4 05H : Text 1 06H : Text 2 07H : Text 3 08H : Text 4 Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 09H fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-11. ORIENTATION SET ********************************************************************** Function: This command sets the orientation of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 0AH fixed DATA02 Setting Value 00H : Desktop Front 01H : Ceiling Rear 02H : Desktop Rear 03H : Ceiling Front Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 0AH fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-12. BACKGROUND SET ********************************************************************** Function: This command sets the background of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 0BH fixed DATA02 Setting Value 00H : Blue 01H : Black 02H : Logo Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 0BH fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-23. AUTO START SET ********************************************************************** Function: This command sets the auto start select of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 16H fixed DATA02 Setting Value 00H : OFF 01H : ON Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 16H fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-24. POWER MANAGEMENT SET ********************************************************************** Function: This command sets the power management of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 17H fixed DATA02 Setting Value(!!) M402 +---------------+------------+ | Setting Value | DATA02 | +---------------+------------+ | 00H | OFF | | 01H | 0:05 | | 02H | 0:10 | | 03H | 0:15 | | 04H | 0:20 | | 05H | 0:30 | | 06H | 1:00 | +---------------+------------+ NP4000s/NP61s/NP215s/NP64s/U300/VE282/PE401 +---------------+------------+ | Setting Value | DATA02 | +---------------+------------+ | 00H | OFF | | 01H | 0:05 | | 02H | 0:10 | | 03H | 0:20 | | 04H | 0:30 | +---------------+------------+ Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 17H fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: (!) On the NP61 series, "Power Management" has been changed to "Auto Power Off". (!!) On the U300 series, set minutes value. 098-27. FAN MODE SET ********************************************************************** Function: This command sets the fan mode of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 1AH fixed DATA02 Setting Value 00H : AUTO 01H : HIGH SPEED 02H : HIGH ALTITUDE Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 1AH fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-30. CONTROL PANEL KEY LOCK SET ********************************************************************** Function: This command sets the control panel key lock of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 1DH fixed DATA02 Setting Value 00H : Disable 01H : Enable Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 1DH fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-32. COMMUNICATION SPEED SET ********************************************************************** Function: This command sets the communication speed of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 1FH fixed DATA02 Setting Value 00H : 4800bps 01H : 9600bps 02H : 19200bps 03H : 38400bps Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 1FH fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-33. DEFAULT SOURCE SELECT SET ********************************************************************** Function: This command sets the default source select of projector. Command: 03H B1H 00H 00H 03H DATA01 .. DATA03 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 20H fixed DATA02 .. 03 Update target +--------+--------+---------------------------------+ | DATA02 | DATA03 | Setting Value | +--------+--------+---------------------------------+ | 00H | 00H | Last | | 00H | 01H | Auto | | 00H | 02H | Select | | 01H | 00H | COMPUTER1 | | 01H | 01H | COMPUTER2 | | 01H | 02H | COMPUTER3 | | 01H | 03H | COMPONENT | | 01H | 04H | VIDEO | | 01H | 05H | S-VIDEO | +--------+--------+---------------------------------+ Response: At the time of a success 23H B1H 01H xxH 03H DATA01 .. DATA03 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 20H fixed DATA02 Update target ( Same as DATA02 of the transmit data ) DATA03 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-34. PROJECTOR ID ENABLE SET ********************************************************************** Function: This command sets the projector ID enable of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 21H fixed DATA02 Setting Value 00H : Disable 01H : Enable Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 21H fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-35. PROJECTOR ID SET ********************************************************************** Function: This command sets the projector ID of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 22H fixed DATA02 Setting Value Projector ID ( Control ID ) 1 .. 254 Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 22H fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-39. TEST PATTERN SET ********************************************************************** Function: This command sets the test pattern of projector. Command: 03H B1H 00H 00H 04H DATA01 .. DATA04 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 26H fixed DATA02 .. 03 Setting Value (Pattern ID) +--------------------------+-----------------+ | Pattern ID | | +--------+--------+--------| Pattern Name | | DATA02 | DATA03 | DATA04 | | +--------+--------+--------+-----------------+ | 02H | 00H | 07H | Cross Hatch | | 04H | 00H | 07H | Raster(0%) | | 05H | 00H | 07H | Raster(25%) | | 06H | 00H | 07H | Raster(50%) | | 07H | 00H | 07H | Raster(100%) | | 07H | 00H | 01H | Raster Red | | 07H | 00H | 02H | Raster Green | | 07H | 00H | 04H | Raster Blue | | 19H | 00H | 04H | Blue Raster 60 | | 17H | 00H | 07H | Gray Raster 10 | | 0AH | 00H | 07H | Gray Raster 30 | | 20H | 00H | 07H | Ramp H | | 20H | 00H | 01H | Red Ramp H | | 21H | 00H | 07H | Ramp V | +--------+--------+--------+-----------------+ Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 26H fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-88. LAMP SELECT SET ********************************************************************** Function: This command sets the Lamp Select of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 57H fixed DATA02 Setting Value 00H : Dual 01H : Lamp1 02H : Lamp2 Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 57H fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-89. LAMP INTERVAL SET ********************************************************************** Function: This command sets the Lamp Interval of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 58H fixed DATA02 Setting Value 00H : Auto 01H : 1 week 02H : 4 weeks 07H : 2000H 09H : 12H 0AH : 24H Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 58H fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-148. KEYSTONE SELECT SET ********************************************************************** Function: This command sets the Keystone Select. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 93H fixed DATA02 Setting Value 00H : Auto 01H : Manual Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 93H fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-174. REMOTE SENSOR SET ********************************************************************** Function: This command sets the Remote Sensor. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 ADH fixed DATA02 Setting Value 00H : Front/Rear 01H : Front 02H : Rear Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 ADH fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-196. WXGA MODE SETTING SET ********************************************************************** Function: This command sets the WXGA Mode of projector. Command: 03H B1H 00H 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 C3H fixed DATA02 Setting Value 00H : OFF 01H : ON Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 C3H fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 098-239. 3D MODE SET ********************************************************************** Function: This command sets the 3D mode for current selected terminal of the projector. Command: 03H B1H 00 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 DBH fixed DATA02 Setting Value 00H : Disable 01H : Enable Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 DBH fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: This command is available only when displaying an image. 098-240. DLP Link SET ********************************************************************** Function: This command sets the DLP Link for current selected terminal of the projector. Command: 03H B1H 00 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 DCH fixed DATA02 Setting Value 00H : Disable 01H : Enable Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 DCH fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: This command is available only when displaying an image. On V300 series, this command will not work for VIDEO or S-VIDEO source. 098-241. 3D FORMAT SET ********************************************************************** Function: This command sets the 3D format for current selected terminal of the projector. Command: 03H B1H 00 00H 02H DATA01 DATA02 CKS (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 DDH fixed DATA02 Setting Value V300/VE282/M402 +----------------------------+--------+-------+------+ | | DATA02 | V300 | M402 | | | | VE282 | | +----------------------------+--------+-------+------+ | Frame Sequential | 00H | * | * | | Top and Bottom (Over/Under)| 01H | * | * | | Side by Side | 02H | x | * | | Frame Packing | 03H | x | * | | Auto | 04H | x | * | +----------------------------+--------+-------+------+ Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 DDH fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: This command is available only when displaying an image. On V300 series, this command will not work for VIDEO or S-VIDEO source. 098-242. 3D L/R INVERT SET ********************************************************************** Function: This command changes the order of displaying image for left eye and right eye. Command: 03H B1H 00H 00H 01H DEH 93H Response: At the time of a success 23H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ----------------------------------------------------------------- DATA01 DEH fixed DATA02 Results 00H : Normal 01H : Error Response: At the time of a success A3H B1H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: This command is available only when displaying an 3D image. This command is not available under the following conditions: - when an image is frozen or muted On V300 series, this command is available only when DLP Link is enabled. 110. AUTO FUNCTIONS EXECUTE ********************************************************************** Function: This command executes the auto functions. Command: 03H B6H 00H 00H 01H DATA01 CKS (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Execution items +-----+---------+ | | Focus | +-----+---------+ | 00H | ! | | 01H | * | +-----+---------+ !: According to projector setting *: Executing Response: At the time of a success 23H B6H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 Execution items(Same as DATA01 of the transmit data) DATA02 Results 00H : Normal 01H : Error Response: At the time of a failure A3H B6H 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 305-1. BASE MODEL TYPE REQUEST ********************************************************************** Function: This command acquires the projector type. Command: 00H BFH 00H 00H 01H 00H C0H Response: At the time of a success 20H BFH 01H xxH 10H DATA01 ... DATA16 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 00H fixed DATA02 ... 03 Projector type See DATA13...14 DATA04 ... 12 Model name (NULL termination character string) DATA13 ... 14 Projector type +--------+--------+--------+--------+-------------------+ | DATA02 | DATA03 | DATA13 | DATA14 | | +--------+--------+--------+--------+-------------------+ | 02H | 05H | 00H | 05H | HT410 | | 02H | 05H | 00H | 05H | HT510 | | 02H | 02H | 00H | 05H | LT180 | | 02H | 02H | 00H | 06H | LT25/30/35 | | 02H | 02H | 00H | 07H | NP40/50/60 | | 03H | 08H | 00H | 07H | NP4000/4001 | | 03H | 08H | 00H | 10H | NP4100 | | 03H | 08H | 01H | 10H | NP4100W | | FFH | 11H | 00H | 00H | NP41/61 | | FFH | 11H | 01H | 00H | NP52/62 | | FFH | 11H | 00H | 12H | NP64 | | FFH | 11H | 01H | 12H | NP54 | | FFH | 11H | 02H | 12H | NP63 | | FFH | 11H | 03H | 12H | NP43 | | FFH | 11H | 04H | 12H | NP53 | | FFH | 11H | 00H | 11H | NP215 | | FFH | 11H | 01H | 11H | NP210 | | FFH | 11H | 02H | 11H | NP115 | | FFH | 11H | 03H | 11H | NP110 | | FFH | 11H | 04H | 11H | NP216 | | FFH | 14H | 01H | 10H | NP-U250X | | FFH | 14H | 02H | 10H | NP-U300X | | FFH | 14H | 03H | 10H | NP-U260W | | FFH | 14H | 04H | 10H | NP-U310W | | FFH | 14H | 00H | 11H | NP-PE401H | | FFH | 16H | 00H | 10H | NP-V300X | | FFH | 16H | 01H | 10H | NP-V260X | | FFH | 16H | 02H | 10H | NP-V230X | | FFH | 16H | 03H | 10H | NP-V260 | | FFH | 16H | 04H | 10H | NP-V230 | | FFH | 16H | 05H | 10H | NP-V300W | | FFH | 16H | 06H | 10H | NP-V260W | | FFH | 16H | 07H | 10H | NP-V260R | | FFH | 16H | 00H | 11H | NP-VE282X | | FFH | 16H | 01H | 11H | NP-VE281X | | FFH | 16H | 02H | 11H | NP-VE280X | | FFH | 16H | 03H | 11H | NP-VE282 | | FFH | 16H | 04H | 11H | NP-VE281 | | FFH | 16H | 05H | 11H | NP-VE280 | | FFH | 22H | 00H | 10H | NP-M402X | | FFH | 22H | 01H | 10H | NP-M362X | | FFH | 22H | 02H | 10H | NP-M322X | | FFH | 22H | 03H | 10H | NP-M282X | | FFH | 22H | 04H | 10H | NP-M402W | | FFH | 22H | 05H | 10H | NP-M362W | | FFH | 22H | 06H | 10H | NP-M322W | | FFH | 22H | 07H | 10H | NP-M332XS | | FFH | 22H | 08H | 10H | NP-M352WS | | FFH | 22H | 09H | 10H | NP-M302WS | +--------+--------+--------+--------+-------------------+ DATA15 ... 16 Reserved Response: At the time of a failure A0H BFH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 305-2. VERSION INFORMATION REQUEST ********************************************************************** Function: This command acquires imformations of projector. Command: 00H BFH 00H 00H 02H 01H 06H CKS (*3) Response: At the time of a success 20H BFH 01H xxH 12H DATA01 �` DATA12 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 01H fixed DATA02 06H fixed DATA03-DATA18 Serial Number (NULL termination character string) Response: At the time of a failure A0H BFH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) 305-3. PROJECTOR INFORMATION REQUEST ********************************************************************** Function: This command acquires basic operation states of projector. Command: 00H BFH 00H 00H 01H 02H C2H Response: At the time of a success 20H BFH 01H xxH 10H DATA01 ... DATA16 CKS (*1) (*2) (*3) Data Portion Contents ------------------------------------------------------------------- DATA01 02H fixed DATA02 Projector Processing Status 00H : Idle 04H : Power On 05H : Cooling 06H : Idle(Error Standby) Other : Not Support Other than above : (nondisclosure) internal use of code during a state transition period DATA03 Indicate Contents 00H : Picture signal displaying 01H : No Signal 02H : Viewr displaying 03H : Test Pattern displaying 04H : LAN displaying 05H : Test Pattern (User) displaying 10H : Signal selection in progress Other : Not Support DATA04 Select source input type 1 01H : 1 02H : 2 03H : 3 04H : 4 05H : 5 Other : Not Support DATA05 Select source input type 2(!) 01H : COMPUTER (RGB) 02H : VIDEO 03H : S-VIDEO 04H : COMPONENT 05H : Reserved 06H : DIGITAL 07H : VIEWER 08H : SLOT1 09H : SLOT2 0AH : SLOT3 0BH : SLOT4 0CH : DIGITAL2 0DH : SCART 10H : AUTO FFH : Not Source Input Other : Not Support DATA06 Indication signal type (Effective only when Select source input type 2 is 02H or 03H) x0H : NTSC3.58 x1H : NTSC4.43 x2H : PAL x3H : PAL60 x4H : SECAM x5H : B/W60 x6H : B/W50 x7H : PALNM x8H : NTSC3.58 LBX x9H : NTSC3.58 SQZ xAH : COMPONENT(60Hz) xBH : COMPONENT(50Hz) xCH : Un known xDH : NTSC xEH : PAL-M xFH : PAL-N FFH : Not Video Input Other : Not Support DATA07 Picture Mute 00H : OFF 01H : ON DATA08 Sound Mute 00H : OFF 01H : ON DATA09 On-screen mute 00H : OFF 01H : ON DATA10...DATA16 Reserved Response: At the time of a failure A0H BFH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) Supplement: (!) On the U300 series, this parameter becomes FFH when non signal. 307. AUTO ADJUST EXECUTE 2 ********************************************************************** Function: This command executes the Auto Adjust. Command: 03H BAH 00H 00H 01H 00H BEH Response: At the time of a success 23H BAH 01H xxH 01H 00H CKS (*1) (*2) (*3) Response: At the time of a failure A3H BAH 01H xxH 02H DATA01 DATA02 CKS (*1) (*2) (*4) (*3) ====================================================================== 5. Response ---------------------------------------------------------------------- * At the time of a success( ACK ) This returns ACK without adding data portion to the command that does not request data. This returns ACK with adding data to the data portion for the command that requests data. * At the time of a failure( NAK ) This adds a cause of not accepting the command to data portion to return it. (Example) Power On Command: 02H 00H FFH F0H 00H CKS NAK: A2H 00H 01H 20H 02H DATA01 DATA02 CKS ====================================================================== 6. Table of Response Error Codes ---------------------------------------------------------------------- +------------+------------+--------------------------------------+ | DATA01 | DATA02 | | | | Error | | | Error types| description| Error contents | +------------+------------+--------------------------------------+ | 00H | 00H | Unknown command | | 00H | 01H | The current model does not support | | | | this function. | | 01H | 00H | Unvalid values specified. | | 01H | 01H | Specified terminal is unavailable or | | | | cannot be selected | | 01H | 02H | Selected language is not available. | | 02H | 00H | Available memory reservation error | | 02H | 02H | Operating memory | | 02H | 03H | Setting not possible | | 02H | 04H | On Forced on-screen mute mode | | 02H | 07H | -No signal- | | 02H | 08H | Displaying a test pattern or PC Card | | | | Files screen. | | 02H | 0AH | Memory operation failed | | 02H | 0DH | Power Off inhibited | | 02H | 0EH | Execution error | | 02H | 0FH | No operation authority | | 03H | 00H | Specified gain number is wrong | | 03H | 01H | Selected gain is not available. | | 03H | 02H | Adjustment failed | +------------+------------+--------------------------------------+